Jump to content
Ultimaker Community of 3D Printing Experts

3D Prints

1,066 files

  1. Roue Robot

    Création d une roue en ABS pour un robot tondeuse
    Diamètre 18 Cm 
    Hauteur 2 cm 
    axe moteur 6mm 
    buse  0.4mm / couche 0.2mm / 6 heures 

    42 downloads

       (0 reviews)

    0 comments

    Submitted

  2. Smartphone Stand Round and Round

    elegant swinging smartphone stand
    The idea was a smartphone stand, where you have the ability to connect your standard charging cable...
    ... and then inspiration began to flow...

    348 downloads

       (0 reviews)

    0 comments

    Updated

  3. Asian Style Clouds

    Hi everyone
    the sun is finally back, and i sculpted asian style clouds (I miss clouds ^^)
     
    Print settings :
    Machine : UM2, bondtech feeder, Olsson bloc
    Nozzle : 1mm
    Walls : 3
    Layerheight : 200µm
    Infill : 0%
    Speed : 45mm/s
    Fan speed : 100%
    Temperature : 200° / 60°
    Bed adhesion : Supports + Brim
     
    Filament used : Colorfabb / Formfutura / SOVB3D / Biofila by Two Bears
     
    You can find the clouds stl here --> https://cults3d.com/en/users/LeKid/creations
     

    23 downloads

       (0 reviews)

    1 comment

    Submitted

  4. Full size Velociraptor skeleton

    Here is my full size Velociraptor skeleton. Juste made for the challenge.
    Lenght: ~180cm
    Sculpted with Zbrush.
    Total printing time: ~392h.
    Printer: Ultimaker2+
    Filament: PLA
    Speed: 30mm/s - 50mm/s
    Nozzle: 0,4mm
    Layers: 0,15mm
    Painting : acrylic paint (spray and brushe) 

    324 downloads

       (2 reviews)

    11 comments

    Submitted

  5. Cloud

    Here is a small cloud I sculpted inside ZBrush last week ;)
     
    some informations about the print :
     
    Printer : UM2 + Olsson Block + Bondtech Feeder
    Nozzle : 0.6mm
    LayerHeight : 200µm
    Wall : 3 (1.8mm)
    Top/Bottom : 6 layers (1.2mm)
    Infill : 15%
    Temp : Nozzle -> 200° / Bed -> 60°
    Speed : 55mm/s (1st layer at 35mm/s)
    Printed with the tip in the air
    Supports : 50° / 15% in density
     
    Total printing : almost 1h
     
    Concerning the sanding process, I started with a grain at 180 and then after 400 to finish at 600 (personally I do not go down in grain it's already quite smooth in 600 :)
     
    I also made a Time Lapse of the sculpting

    42 downloads

       (0 reviews)

    3 comments

    Updated

  6. Darwin Barcode

    Design by @lekid
     
    Inspired by a picture found on internet
     
    Printed with Polymaker Polysmooth filament and polished with the Polysher
     
    Then glued on a glass frame of 30cm x 60cm

    43 downloads

       (2 reviews)

    0 comments

    Updated

  7. Filament verbinden/ Filament splicing Tutorial

    German:
    Hier zeige ich eine Möglichkeit die Enden von fast leeren Filamentspulen miteinander zu verbinden.
    Für weitere Details siehe Video.

    English:
    Here I show you a way to connect the ends of almost empty filament spools.
    For more details watch the video.
     
     
    Pinshape:
    https://pinshape.com/items/42163-3d-printed-filament-verbinden-filament-splicing-tutorial
    Youmagine:
    https://www.youmagine.com/designs/filament-verbinden-filament-splicing
    Thingiverse:
    https://www.thingiverse.com/thing:2762715
     
     
    Video:
    https://youtu.be/xalpQIuSumg

    25 downloads

       (0 reviews)

    0 comments

    Updated

  8. Filament holder for the UM3 spools

    My special designed filament holder are directly for the original ULTIMAKER 3 (UM3) spools.
    Until now I use it for the 350g and 750g spools of 2.85mm filament (see pictures).
    Advantages:
    Easy to clamp or unloose in the spool Best way of storing the filament spools Spools are better stackable No unraveling of the filament End of filament doesn't have to be fixed in the small hole and the danger of breaking filament I'm looking forward to your feedback and especially if it works as well for the other material spools.
    Have fun.
     
    Posted at https://www.thingiverse.com/thing:2746539

    106 downloads

       (0 reviews)

    0 comments

    Submitted

  9. 1/40 Giganotosaurus

    Nozzle : 0.4
    Layer : 0.06
    #dinosaur #giganotosaurus #dino #dinosaurs #figure

    87 downloads

       (2 reviews)

    0 comments

    Submitted

  10. 1/40 Mosasaurus

    1/40 Mosasaurus
    Nozzle : 0.4
    Layer : 0.06

    75 downloads

       (1 review)

    1 comment

    Submitted

  11. Dolphin

    I designed and printed a dolphin jumping out of the sea. The dolphin was printed with Bronzefill. The base was printed using NGEN clear for the outer walls and blue PLA for the infill, thus creating a nice blueish sea.
    Printfiles: https://www.youmagine.com/designs/dolphin 
     
    Marco

    32 downloads

       (0 reviews)

    0 comments

    Submitted

  12. Ultimaker Christmas

    Hi there,
     
    I designed a little dual colour print for christmas 
     
    Print files
     
    Merry Christmas

    13 downloads

       (0 reviews)

    0 comments

    Updated

  13. Dual Balance prototype

    You can find here a new prototype of the Dual Balance system to use a dual extruder and some example things at this links:
    https://www.thingiverse.com/thing:2644923
    https://www.thingiverse.com/thing:2608925
    https://www.thingiverse.com/thing:2593527

    471 downloads

       (0 reviews)

    0 comments

    Updated

  14. The SCAFFOLD water-soluble PVA Wire and POLY PLUS PLA

    You can find here my test with a water-soluble PVA Wire the SCAFFOLD and POLY PLUS PLA in dual material mode.
    After many tests and help with the community, i found this parameters to print the SCAFFOLD with 0.3mm nozzle and the cura 2.7 in 0.2mm per layer. I 'm using a special head "Dual_Balance" but you can also use this paramters with you dual printer with 0.3mm of nozzle. You can find below the picture with all the cura 2.7 parameters for the SCAFFOLD.

    You can find below the picture with all the cura 2.7 parameters for the white POLY PLUS PLA.

    You can find the 3d model with this link:
    https://www.thingiverse.com/thing:2608925
    The only problem that has occurred is a layer that is detached from the tower caused by my setting on CURA to clean the nozzles. so to avoid!






    384 downloads

       (0 reviews)

    0 comments

    Updated

  15. Ultimaker3(E) Fan Bracket Clip

    My fan bracket cover got bent a while back. I had been using rubber bands to hold it in place, but with heating, they would not last. So, having seen several threads of fan covers not staying in place or magnets losing their oomph or whatever, I decided to make this. As you can see, it is on my UM3E and holds quite nicely. The two variations are just one is a slight bit thinner in the back and not as blocky there. The front is blocky to increase the strength of those tiny clasps.
    Print it out in filament that can have a bit of flex and take a bit of heat. I will probably have to print in another material when I return to high heat materials such as PC.

    132 downloads

       (0 reviews)

    0 comments

    Updated

  16. British Bully split test

    Another bully sculpt, now I have American, British and French... was experimenting with zero retractions speed increases and the placements of the slice and how well they stuck together after. Doing a tutorial for the glueing, acetoning, filler and finishing for this. part one is done.
    model available now for download.
     
     
     
     

    353 downloads

       (1 review)

    0 comments

    Updated

  17. Custom mount for IKEA Östanå

    Needed a custom mount for the IKEA Östanå lamp. Couldn't find one so I created one in Fusion 360.
    The two gaskets from the original mount can be used with this mount.

    133 downloads

       (0 reviews)

    0 comments

    Updated

  18. Happy New Ear!!! Work in progress.

    Thank you @vlada.mladenovic for sculpting, modelling 3D ear and @sculptures_unique for idea. @umetnickaskolanis thanks. Working progress. Used PLA @ORBITECH
    And the best 3D printer @ultimaker

    119 downloads

       (0 reviews)

    0 comments

    Updated

  19. Holder for nozzle parts

    Printed with nozzle 0,8mm, blue filament

    2,245 downloads

       (0 reviews)

    1 comment

    Updated

  20. Replacement Radio Knob

    I needed a replacement knob for a vintage transistor radio.  I doubted if I could get the tiny ridges to print but the UM2+ did not disappoint!  Perfect reproduction, ready to use off the printer.

    563 downloads

       (1 review)

    0 comments

    Updated

  21. Test with the new cover DUAL Balance to print the bulbasaur

    This is my first test with the new cover Dual Balance with the Poly Plus PLA and the RED ABS of Ultimaker 1623 to print a new bulbasaur in 0.15 mm per layer with my dual extruder system.
    You can find also the grand brother at this address:
    https://www.thingiverse.com/thing:2644923

    312 downloads

       (0 reviews)

    0 comments

    Updated

  22. 4 bowden support

    Here you can see my last design to maintain 4 bowden and the new connector for the sensor and the heater for ultimaker 2+.
    I designed this 4 bowden support for the Dual_balance system who works in dual mode but you can also use it in simple mode.
    The idea is to soldering together two Double Row Male Breakable Pin Header Connector Strip:
    Brand Name: SHWB Model Number: 2.54 Pin Header
    This Pin header Connector is not very expensive and useful with many standard 2.54 mm male connector (or Male and female). You can find below a exemple.
    https://www.aliexpress.com/item/2pcs-Pitch-2-54mm-80-Pin-2x40Pin-SMT-SMD-Double-Row-Male-Breakable-Pin-Header-Connector/32827789967.html
    And after you can slip this new type of male to male connector inside this 4 bowden support.
    You can find here some example of other 3d printing:
    https://www.thingiverse.com/thing:2582766

    387 downloads

       (0 reviews)

    0 comments

    Updated

  23. New print

    New print

    15 downloads

       (0 reviews)

    0 comments

    Updated

  24. 3D Print a 1:100 scale concept model for a house

    3D Print a 1:100 scale concept model for a house, the dominant repeated ribs and front loft space accessed by a spiral stair recall timber framed ships.
    Printed on the Ultimaker 3 we used the standard medium print settings for most of the model, with the high settings required for some of the highly intricate pieces like the screens.

    270 downloads

       (0 reviews)

    0 comments

    Updated

  25. iPhone X Dock

    Why another phone dock?
    The new iPhone X is a few mm taller than the previous phones, so my old printed iPhone dock didn't work anymore. After some browsing I could not find any other dock I liked. The one I liked that doesn't fit does not exist for the X and I dislike mods on STLs/OBJs. The generic ones are typically clumsy or have other issues.
    So I decided to design one quickly from scratch. Here's the result I would like to share.
    I think there are not enough phone docks out there yet! :-)

    330 downloads

       (0 reviews)

    1 comment

    Updated

×
×
  • Create New...