Jump to content
Ultimaker Community of 3D Printing Experts

3D Prints

1,066 files

  1. My First Successful Ultem 1010 benchy on UM2+

    This is my first benchy in a HT material, material used is Ultem1010, nozzle temperature 370C and bed temp is 160C

    295 downloads

       (0 reviews)

    0 comments

    Updated

  2. Model of Stark Towers as used in 'Avengers Age of Ultron'

    During my spell working in the Art department on 'Avengers Age of Ultron' I was asked by the production designer to build a prop to help dress the interior set of 'Stark Towers' The model was to show the new section of tower that replaced the damaged section from the original film. As I only had 4 weeks to build it (including 3d modelling) we needed to simplify the design a bit, hence the lower portion being in laser cut acrylic.
    Using my trusty Ultimakers I think I pulled off the desired effect, even if it only appeared in the movie for less than a second!

    2,890 downloads

       (2 reviews)

    3 comments

    Updated

  3. PEEK benchy made on UM2+

    PEEK benchy made on UM2+

    275 downloads

       (0 reviews)

    0 comments

    Submitted

  4. Ultem 9085 Benchy

    Ultem 9085 Benchy

    266 downloads

       (1 review)

    0 comments

    Submitted

  5. PVA Reel casing

    because I print continuously I don't unload the PVA.  As a consequence I have an issue with moisture so I designed a casing to minimise the moisture exposure.  basically I created two pockets for silica gel packets and a tube.  it allows the reel to rotate freely.  in addition I put it in a bag along with more silica  gel.  
    so far I haven't heard a pop lol
    I printed it on my UM 2+ but I think it will go on a UM 3 but not tried it yet.
    Rebekah Anderson

    351 downloads

       (0 reviews)

    0 comments

    Updated

  6. Vaporeon!

    Time to move on, enough Pokémons printed for friends
    Instagram post here!

    1,125 downloads

       (0 reviews)

    1 comment

    Updated

  7. New print

    New print

    0 downloads

       (0 reviews)

    0 comments

    Submitted

  8. Lotus Lights

    Printed in 3 parts.
    Hight: 340mm
    Diam: 120mm

    763 downloads

       (0 reviews)

    0 comments

    Updated

  9. Sonos Plateau allowing you to put extra stuff on top of it

    I thought I could save some space on the desk of my daughter with putting the desk lamp on top of the Sonos speaker. You can't put something on it without blocking the buttons so I created this.

    996 downloads

       (0 reviews)

    0 comments

    Updated

  10. New print

    New print

    0 downloads

       (0 reviews)

    0 comments

    Submitted

  11. Indicatiemeter Filament lengte

    To determine the remaining filament on the coil. Length is an indication between an under and above value. Depending on the number of turns of the filament at a certain distance from the outside of the coil.

    575 downloads

       (0 reviews)

    0 comments

    Updated

  12. Iphone 6 / 6S Holder

    Background
    I found this model in Thingiverse and thought I would print it. It was also the first time I had used Gold PLA.
     

    Print
    For the print I used an 8mm 'Brim' to help adhere the base to the build plate. Recently with printing I have found the 'Brim' no only stops/reduces warping. But it also allows the printer to get settled for the printing task.
     
    Print Settings:
    Layer Height - 0.15 mm
    Wall Thickness - 1.0 mm
    Top/Bottom Thickness - 1.0 mm
    Infill Density - 15 %
    Enable Retraction - Yes
    Print Speed - 40 mm/s
    Travel Speed - 120 mm/s
    Enable Print Cooling - Yes
    Enable Support - No
    Build Plate Adhesion Type - Brim - 8 mm
    Print Sequence - All at once
     
    Sanding / Finishing
    1. Pliers used to remove Brim
    2. Tweezers used to remove Brim inside cable housing
    3. 120 Grit Sandpaper (with water) used on the side to remove Brim
    4. 220 Grit Sandpaper (with water) used on the side to smooth edge
    5. 320 Grit Sandpaper (with water) used on the side to finish edge
     
    Completion
    The print came up in high quality which required some sanding to remove the brim and also the material on the underside of the cable holder housing. This print works very well in holding my phone and amplifying sound.
    This is not my design I got it from: http://www.thingiverse.com/thing:1289078

    1,057 downloads

       (0 reviews)

    0 comments

    Updated

  13. Leopard 2 HO scale 1:87

    Recommended profile
    High quality 0.6mm

    823 downloads

       (0 reviews)

    0 comments

    Updated

  14. Electric Guitar

    Electric Guitar

    1,382 downloads

       (0 reviews)

    0 comments

    Updated

  15. pip boy 3000

    i've do this one for cosplay purpose.

    1,595 downloads

       (0 reviews)

    0 comments

    Updated

  16. Mini Retro Computers

    Mini Retro Computers

    1,389 downloads

       (0 reviews)

    0 comments

    Updated

  17. Maquette Studio Kubuz

    About a mounts ago, I received the ultimaker 2 I've won with the Ultimaker/Oneplus Challenge.
    I promise Sander to add a image of my first print on the forum.
    So I began thinking what object should I print first.
    One thing becomes another, I've printed a example installation for a client.

    2,162 downloads

       (0 reviews)

    0 comments

    Updated

  18. Atlas Titan Arm and Rifle

    This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:
    Quality
    Layer Height: 0.1 mm
    Initial Layer Height: 0.3 mm
    Line Width: 0.4 mm
    Wall Line Width: 0.4 mm
    Outer Wall Line Width: 0.4 mm
    Inner Wall(s) Line Width: 0.4 mm
    Top/Bottom Line Width: 0.4 mm
    Infill Line Width: 0.4 mm
    Skirt/Brim Line Width: 0.4 mm
    Support Line Width: 0.4 mm
    Shell
    Wall Thickness: 0.8 mm
    Wall Line Count: 2
    Top/Bottom Thickness: 0.8 mm
    Top Thickness: 0.8 mm
    Top Layers: 8
    Bottom Thickness: 0.8 mm
    Bottom Layers: 8
    Top/Bottom Pattern: Lines
    Outer Wall Inset: 0 mm
    Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
    Horizontal Expansion: 0 mm
    Z Seam Alignment: Shortest
    Infill
    Infill Density: 25%
    Infill Line Distance: 3.2 mm
    Infill Pattern: Grid
    Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
    Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
    Infill Wipe Distance: 0.1 mm
    Infill Layer Thickness: 0.1 mm
    Gradual Infill Steps: 0
    Infill Before Walls: Check
    Material
    Enable Retraction: Check
    Retraction Extra Prime Amount: 0 mm3
    Retraction Minimum Travel: 0.8 mm
    Maximum Retraction Count: 90
    Minimum Extrusion Distance Window: 6.5 mm
    Standby Temperature: 175°C
    Nozzle Switch Retraction Distance: 16 mm
    Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s
    Speed
    Print Speed: 60 mm/s
    Infill Speed: 80 mm/s
    Wall Speed: 30 mm/s
    Outer Wall Speed: 30 mm/s
    Inner Wall Speed: 60 mm/s
    Top/Bottom Speed 15 mm/s
    Support Speed: 60 mm/s
    Support Infill Speed: 60 mm/s
    Travel Speed: 120 mm/s
    Initial Layer Speed: 15 mm/s
    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 30 mm/s
    Skirt/Brim Speed 15 mm/s
    Maximum Z Speed: 0 mm/s
    Travel
    Combing Mode: All
    Avoid Printed Parts when Traveling: Check
    Travel Avoid Distance: 0.625 mm
    Cooling
    Enable Print Cooling: Check
    Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
    Regular/Maximum Fan Speed Threshold: 10 s
    Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
    Minimum Layer Time: 5 s
    Minimum Speed: 10 mm/s
    Support
    Enable Support: Check
    Support Placement: Everywhere
    Support Overhang Angle: 50°
    Support Pattern: Zig Zag
    Connect Support ZigZags: Check
    Support Density: 30 %
    Support Line Distance: 1.3333 mm
    Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
    Support X/Y Distance: 0.7 mm
    Support Distance Priority: Z overrides X/Y
    Minimum Support X/Y Distance: 0.2 mm
    Support Stair Step Height: 0.3 mm
    Support Join Distance: 2.0 mm
    Support Horizontal Expansion: 0.2 mm
    Use Towers: Check
    Tower Diameter: 3.0 mm
    Minimum Diameter: 3.0 mm
    Tower Roof Angle: 65°
    Build Plate Adhesion
    Build Plate Adhesion Type: Brim
    Skirt/Brim Minimum Length: 250 mm
    Brim Width: 8.0 mm
    Brim Line Count: 20
    Brim Only on Outside: Check
    Mesh Fixes
    Union Overlapping Volumes: Check
    Special Modes
    Print Sequence: All at Once
    Surface Mode: Normal
    Experimental
    Extra Skin Wall Count: 0

    857 downloads

       (0 reviews)

    0 comments

    Updated

  19. PokeWood

    Réalisation d'une PokeWood pour les 20ans de Pokemon.
    Modélisation sous ZBrush et Impresion 3d sur UM2 avec Feeder Bondtech et Bloc Olssen.
    Utilisation des filaments wood de Formfutura Cèdre / Ebène / Pin / Bouleau et Olive.
    -------------
    Realisation of a PokeWood for the 20 years of Pokemon.
    Modeling with ZBrush and 3d Print on UM2 with Bondtech's Feeder and Olssen Bloc.
    Easywood filaments of Formfutura Cedar / Ebony / Pin / Birch and Olive.

    1,284 downloads

       (0 reviews)

    0 comments

    Updated

  20. Ultimaker keychain

    For everyone who want to have keychain with Ultimaker
    Follow me on Facebook : https://www.facebook.com/alen.kuhta/media_set?set=a.971249112929474.1073741827.100001331847671&type=3&pnref=story
    and Twitter : https://twitter.com/a_kuhta
    Thank you.

    452 downloads

       (0 reviews)

    0 comments

    Updated

  21. Tigris Plate test

    Lots of pics...
    Just a quick attempt at acid plating on a failed model (split) after a break from it. but it failed because the copper I'm using is of a different grade than it should be and it just goes weird. Still learning here, just dug up my airbrush from 15 years ago and it still works!!! silver coated before electro bath and voltage was probably too high too. Im gonna try brush plating next. Due to the complete contamination of both copper and solution, a decent plate is not possible anymore but ill keep going till I get nothing.
    Gonna do a vid/thread later about this but i need to figure out whats going wrong first!

    377 downloads

       (0 reviews)

    1 comment

    Updated

  22. 3D Printed + Painted Scorpion/Widow Spaceship

    One of my favorite ship design from the space opera Eve Online. Gave it a quick paintjob.

    573 downloads

       (0 reviews)

    0 comments

    Updated

  23. Happy cat

    Second test print, usual acetone method.

    374 downloads

       (0 reviews)

    0 comments

    Updated

  24. FLORE

    FLORE

    611 downloads

       (0 reviews)

    0 comments

    Updated

  25. New print

    New print

    0 downloads

       (0 reviews)

    0 comments

    Submitted

×
×
  • Create New...