3D Prints
1,105 files
-
Hairy Lion
By Labern
Erik's 3MF Hairy Lion Print.
Printed With Colorfabb which i found needs the standby temp reduced a bit.
1,987 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Octolamp
A Huge Personal Project that took an Eternity to finish
MATERIAL
Bronzefill
NUMBER OF PIECES:
156 unique parts
POST PROCESSING
First stage: 240, 400, 1000 Grit Sandpaper
Second stage: Metal Polish Cream
Final Stage: Vinegar and Marine salt to accelerate oxidation time
MEASUREMENTS & OTHER INFO
Length: 1.00 m
Width : 1.10 m
Height : 0.50 m
Weight: 23 Kg
Volume: 191872,772 cm3
Modeling Time: Around 13 Months
Post Processing Time: around 4 Months
Printing Time: Around 2000 hours
1,893 downloads
(0 reviews)0 comments
Updated
-
Silent printing...
By tinkergnome
Model is the Robot Drone from Silent Running (1971). It consists of several parts, that are glued together.
For some parts I changed the filament color at certain heights (it's not painted in any way).
870 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Projekt M: 3D Printing
By Zeno
Friend of my printed a 1/100 scaled modell (400x800x60 / 50 pieces >3000g) of the upcoming Mellowpark in Berlin which is in crowdfunding now.
https://www.mellowpark.de/
515 downloads
-
Feed neck for paintball marker
By Techniktoni
Made on my modded um2 with platec and S3D slicer.
Dimensions: 3x8 cm
365 downloads
(0 reviews)0 comments
Submitted
-
Dossier Holder (Long print - changing filament)
By yvest
My daughter needed some dossier holder to be used in a large drawer so I came up with this design. Nothing too special although for me it was the first multi-day print as it would take about 45 hrs to print. All went fine although I noticed at some point I was running out of filament. I quickly checked the forum trying to find best ways of changing filament during print but couldn't get quick confirmation on best possible way of doing this (all ways seem to have some pro/cons/risks of bad prints). In the end I went for "soldering" 2 filaments together.
What I did (during printing):
- Took off the filament spool of the holder
- Took off the remaining filament of the spool
- Took a new spool of filament
- Made a straight cut in both filaments
- Heated a soldering iron (not sure about the temp as I can't configure that, I just didn't let it completely heat up)
- Put both end against the soldering iron until it melts a bit
- Then quickly put both ends together
- Once firm, I went with the soldering iron over it again to somehow smooth it little more
From then, I just hoped it would hold, not clutter and print well.
Luckily, it work pretty well. As you can see in one of the images, there is some under extrusion at some point which is for sure when the connected filament got used. But you need to look pretty close to see it so happy with the final result.
Having said that, would love to hear if there are any better ways to change filament when you run out during a print.
348 downloads
(0 reviews)0 comments
Updated
-
Ultimaker 2 dual head
By Roland
...I'm trying to get the UM2 working with dual head.
Now it is working almost good, one of the biggest problems is slicing software with good functions like prime pillar and ooze shield.
Simplify 3D works, but has also some issues with dual extrusion.
In Cura I can't find any support for dual extrusion!?
Roland
1,867 downloads
(0 reviews)0 comments
Updated
-
Velta 3D
By lekid
Hi everyone,
I present you the mascot I modeled for the upcoming B-Velta, a delta type 3d printer made in France.
The gcode of the mascot will be inside the futur printer
Modeling in ZBrush.
2 versions of the model :
Colorfabb Ngen Silver Metallic and Octofiber Light Wood
Total Height : 180mm
Nozzle -> 0.6
Wall -> 1.2
Infill -> 20%
B-Velta -> https://www.facebook.com/BVELTA
My facebook page -> https://www.facebook.com/KevinPalluet.MIP
631 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Submitted
-
(0 reviews)0 comments
Updated
-
Mecha Dunkleosteus head
By cloakfiend
Just a quick mess around to tst if my coupler is dead. And yes it is, lol. I wont be printing fpr a while, been needing to do some maintenace for a while now. Forgot infill as well! lol, surprised it didn't fail completely . Will do a rigged one next fpr fun, I really liked the skull of this fish had top make my own version!!
490 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Submitted
-
Ultimaker 2 Breathable Electronics Enclosure
I wanted an enclosure for the UM2 that allowed the electronics to breathe more.
I had a hard time getting this to work. At first I tried to put all of the holes in the bottom face in the part model. But all those little perimeters made it difficult to print.
So I made the bottom side of the enclosure solid in the model.
In the slicer software (S3D), I set the number of top and bottom layers both to zero. And I set the number of shells to 10.
It didn't print perfect, but it printed better than any of my previous attempts.
409 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Ultimaker 2 Camera Mount
By meduza
I wanted a more integrated solution for mounting a Raspberry Pi Camera on the UM2, so i designed one.
I am using a third-party camera module with a 36x36mm board and a M12 lens mount.
5,168 downloads
(0 reviews)0 comments
Updated
-
Vertical Axis Wind Turbine (VAWT)
By Ultimaker
This Vertical Axis Wind Turbine (VAWT) was made by @Valcrow for the new Ultimaker 2+. To make it yourself you can visit YouMagine to download the files and our Wind Turbine print tutorial for print/assembly tips.
The Ultimaker 2+ desktop 3D printer is based on the award-winning Ultimaker 2 and features all of our latest innovations and understanding of 3D printing.
7,968 downloads
-
Grayscale can (linear halftoning)
By Guest maht
This is an example of a grayscale print that can be achieved with an unmodified Ultimaker 3. This was designed and textured by Beerend Groot.
Greyscale printing is achieved using a technique known as linear halftoning. With most 3D prints, you are limited to monochrome, but this allows you to print items in two colors, giving an item enhanced depth, definition, and realism when compared to a monochrome print.
I have written an article about it here.
The feature is not implemented properly in to Cura at this time, but there are instructions of how to test it (for experienced users!) instructions for this and a discussion on the forum can be found here.
1,410 downloads
-
HeadLight for UM2
By darkdvd
More info here (in french) : https://ultimaker.com/en/community/39373-eclairage-supplementaire-au-niveau-de-la-tete?page=2&sort=#reply-176952
881 downloads
(0 reviews)0 comments
Updated
-
3D Printed Drag Knife
By ignatius
To improve the CNC Router and not just to drill stuff, I also wanted to cut materials like cardboard, vinyl, paper, etc.
Before to buy a lasercut, I did find in Internet a very interesting tool to transform the Spindle into a cutting machine.
I wanted to buy the knife tool, but my spindle collet is 8mm, and most of the tools I saw doesn´t fit on it, so I decide to make my own, and after some failed prototypes and test, I made one that until now, after several test it works just great!.
The blade can be coupled in two different positions, with a cut depth of 6mm or 10mm.
Component list:
- 2x bearings with 8mm inner diameter
- 1x 8mm x 50mm rod
- 2x collar
- 9x M3 30mm screws with nuts and washers
- 2x M3 16mm screws with nuts and washers
- Blades
I spend like 30€ on components, but that´s because I bought more than I needed, just to have spare parts, and the 3D printed parts, cost like 2€ with a 2,2kg Colorfabb XT Spoon.
6,431 downloads
(2 reviews)0 comments
Updated
-
2 new printed nylon axis give this lawn mower a 2th life.
By ultiarjan
got the broken discarded machine for free and just used it for the first time, working pretty nice.
472 downloads
(0 reviews)0 comments
Updated
-
3d House
By VitR
Hi ultimakers,
Here is one of my projects which is made on Ultimaker3.
1,080 downloads
(0 reviews)0 comments
Updated
