Ultimaker Cura

8,616 topics in this forum

1. QUESTION Cura settings: Improving naming and descriptions

   By maht, July 10   

   • ULTIMAKER
   • 8 replies
   • 764 views
   • 
   • kayakbabe
   • Friday at 03:51 AM

2. Cura settings explained

   By SandervG, July 1
   • 6 replies
   • 440 views
   • 
   • leliep
   • July 15

3. Ultimaker Cura 4.6 released 1 2 3

   By maht, April 21   

   • CURA
   • 58 replies
   • 7,794 views
   • 
   • toothpaste
   • June 13

4. Error Message when opening Cura

   By kenny, yesterday at 10:17 PM   

   • ULTIMAKER
   • QUESTION
   • 3 replies
   • 44 views
   • 
   • kenny
   • 1 hour ago

5. No skin printed for Ender Pro

   By degsme, 6 hours ago
   • 4 replies
   • 22 views
   • 
   • Smithy
   • 3 hours ago

6. Prime tower for first layer

   By YUVL, 17 hours ago   

   • QUESTION
   • 1 reply
   • 34 views
   • 
   • burtoogle
   • 4 hours ago

7. Nothing? Where’s my print?

   By Roju, 8 hours ago   

   • QUESTION
   • 3 replies
   • 24 views
   • 
   • Roju
   • 5 hours ago

8. fundamental problem with cura (extrusion rate)

   By esopalumpa, 6 hours ago   

   • REQUEST
   • 0 replies
   • 21 views
   • 
   • esopalumpa
   • 6 hours ago

9. Cura MP10 settings

   By MarkAM, February 6   

   • CURA
   • 17 replies
   • 1,791 views
   • 
   • p_j_w
   • 6 hours ago

10. Cura 4.6.1 segfaulting with Artemis/Duet

    By brianmichalk, Saturday at 09:44 PM
    • 2 replies
    • 49 views
    • 
    • brianmichalk
    • 9 hours ago

11. Cura 4.6.2 - Where is the Nozzle settings?

    By pa_trick, July 27
    • 8 replies
    • 214 views
    • 
    • AnthonyJackman
    • 10 hours ago

12. SOLVED Everything is about .4 mm too big

    By Thick8, March 22   

    • HELP
    • 6 replies
    • 297 views
    • 
    • paxpring
    • 10 hours ago

13. Marketplace installed materials not showing up

    By willcaddy, 12 hours ago
    • 4 replies
    • 30 views
    • 
    • willcaddy
    • 11 hours ago

14. Igus Iglidur 180 not showing in Cura

    By RudydG, Saturday at 06:17 AM
    • 1 reply
    • 28 views
    • 
    • nallath
    • 16 hours ago

15. All printer settings and materials lost

    By Nexnex77, 18 hours ago
    • 2 replies
    • 27 views
    • 
    • nallath
    • 16 hours ago

16. Cura 4.4 object view is black shadow only

    By OleBruun, December 11, 2019   

    • CURA
    • 3 replies
    • 324 views
    • 
    • vicmbz
    • 17 hours ago

17. Brim only on the outside of object?

    By netsrac, July 21, 2014
    • 12 replies
    • 4,143 views
    • 
    • Adam324
    • Yesterday at 07:41 PM

18. Looseness around holes 1 2 3 4

    By Deve, May 27, 2018
    • 76 replies
    • 6,595 views
    • 
    • Adam324
    • Yesterday at 03:27 PM

19. Thin gap between outer wall and inner wall, only on small circular insets but not on the perimeter of the print...

    By roykinn7, August 25, 2017
    • 16 replies
    • 7,661 views
    • 
    • henderpa
    • Yesterday at 09:43 AM

20. G2, G3 generated in slicer?

    By drmike, Friday at 10:02 PM   

    • QUESTION
    • 3 replies
    • 57 views
    • 
    • drmike
    • Saturday at 01:45 PM

21. How do I 3d print from an ender 3 pro?

    By davidstone11, Friday at 11:52 PM
    • 17 replies
    • 102 views
    • 
    • Enigma_M4
    • Saturday at 11:40 AM

22. Per Model Settings

    By webers, Friday at 12:20 PM
    • 4 replies
    • 67 views
    • 
    • Mari
    • Saturday at 10:39 AM

23. Primary mesh control

    By SimonG, Saturday at 04:42 AM
    • 1 reply
    • 36 views
    • 
    • burtoogle
    • Saturday at 08:07 AM

24. How are cura settings stored?

    By KJackson, Saturday at 12:07 AM   

    • QUESTION
    • 2 replies
    • 48 views
    • 
    • ahoeben
    • Saturday at 06:42 AM

25. overhang settings vs tree support

    By brunoosti, Friday at 11:35 PM
    • 0 replies
    • 36 views
    • 
    • brunoosti
    • Friday at 11:35 PM