Ultimaker Cura

10,219 topics in this forum

1. Cura settings explained 1 2 3

   By SandervG, July 1, 2020
   • 63 replies
   • 8.1k views
   • 
   • GregValiant
   • May 15

2. Ultimaker Cura 4.10 1 2 3

   By fvrmr, June 29   

   • Ultimaker
   • 57 replies
   • 2.1k views
   • 
   • nallath
   • July 20

3. We want to learn about your Cura workflows!

   By 10r3n20, June 14   

   • Question
   • Ultimaker
   • 6 replies
   • 295 views
   • 
   • 10r3n20
   • June 29

4. A new design has been posted on YouMagine! 1 2 3 4 49

   By ErikDeBruijn, August 14, 2013
   • 1.2k replies
   • 116.7k views
   • 
   • ultibrain
   • August 29, 2014

5. Cura settings for Prusa i3

   By carmamir, July 12, 2013
   • 3 replies
   • 81k views
   • 
   • nutz95
   • September 12, 2013

6. Best Support Settings in Cura for Ease of Removing?

   By BumbleDuck, December 6, 2016
   • 18 replies
   • 75.9k views
   • 
   • BMacCartney
   • April 27, 2017

7. 2 ways to resume print from last layer

   By tonycstech, August 4, 2014
   • 19 replies
   • 67.5k views
   • 
   • jpuyhab
   • March 15

8. How can I print directly from cura to my 3d printer using usb? 1 2 3

   By chumlee, July 19, 2016
   • 64 replies
   • 67k views
   • 
   • GregValiant
   • May 17

9. Does Cura have a Vase mode?

   By Gencab, December 11, 2016
   • 1 reply
   • 60.2k views
   • 
   • Gencab
   • December 11, 2016

10. Changing Cura generated start code 1 2

    By ex-egll, June 20, 2017
    • 46 replies
    • 55.8k views
    • 
    • Mari
    • July 1, 2020

11. How to use support blocker???

    By klaus_kraemer, April 30, 2018
    • 23 replies
    • 52.4k views
    • 
    • nallath
    • October 22, 2020

12. How to configure Marlin Firmware yourself? Heated print bed problem 1 2

    By isphording90, April 21, 2013
    • 33 replies
    • 52k views
    • 
    • gr5
    • May 20, 2014

13. Cura 2.1 open beta has been released! 1 2 3 4 12

    By SandervG, April 13, 2016
    • 296 replies
    • 51.8k views
    • 
    • DaHai8
    • October 21, 2016

14. Dividing a Large Print into Several Smaller Prints

    By printerfan, November 26, 2014
    • 17 replies
    • 50.2k views
    • 
    • CLJ
    • July 13, 2018

15. Duplicate parts / model in Cura

    By francoisba, June 23, 2015
    • 4 replies
    • 50.2k views
    • 
    • MalFie
    • January 3

16. Introducing The Experimental Bridging Settings 1 2 3 4 5

    By burtoogle, March 27, 2018   

    • CURA
    • BETA
    • 117 replies
    • 48.7k views
    • 
    • minercraftal
    • April 30

17. Support structure not appearing in Cura

    By lordarchiebald, April 26, 2015   

    • HELP
    • CURA
    • 6 replies
    • 45.3k views
    • 
    • Blz
    • December 7, 2019

18. Retraction Extra Prime Amount - Suggested Values?

    By DaHai8, October 9, 2016
    • 15 replies
    • 44.4k views
    • 
    • Adam324
    • March 16, 2019

19. Cura 2.1.2 Support types Which works best?

    By LePaul, August 4, 2016
    • 16 replies
    • 43.9k views
    • 
    • Labern
    • August 6, 2016

20. Simplify3D 1 2 3 4 11

    By conz, July 9, 2014
    • 252 replies
    • 43.5k views
    • 
    • LePaul
    • April 13, 2017

21. Is there a way to 'measure' in CURA

    By jweaver, March 17, 2015
    • 3 replies
    • 43.4k views
    • 
    • jweaver
    • March 17, 2015

22. Binaryt vs ASCII *.stl

    By mastory, February 26, 2012
    • 2 replies
    • 42.5k views
    • 
    • Daid
    • February 26, 2012

23. "perfect" start.gcode & end.gcode for Cura 15.04.2 (Mac) for Octoprint

    By frederiekpascal, September 12, 2015
    • 3 replies
    • 42.5k views
    • 
    • rigs
    • September 13, 2015

24. Raft Settings

    By bagel-orb, November 5, 2014
    • 14 replies
    • 41.9k views
    • 
    • kenzu
    • January 6, 2015

25. Installing OctoPrint for the Ultimaker 2 1 2

    By DidierKlein, April 9, 2014
    • 45 replies
    • 41k views
    • 
    • Melka
    • December 19, 2016