Jump to content

UltiMaker Cura

The world's most popular 3D printing software. Made together with the community. 

13,492 topics in this forum

  1. Better method to using Replicator 2 printers with Cura

    By jessecake,
    • 19 replies
    • 19k views

  2. Touchscreen support?

    By isNate,   
    • 5 replies
    • 1.8k views

  3. Cura positions part below the build surface 1 2

    By GrimJeeper91,
    • 35 replies
    • 12.5k views

  4. Troubles in ultimaker cura

    By wingman123,
    • 1 reply
    • 157 views

  5. Linear Advance not working in Cura 5.6

    By FBAone2,
    • 6 replies
    • 379 views

  6. Printing with ultimaker S5 gonne wrong

    By wingman123,
    • 1 reply
    • 189 views

  7. Per model settings: changing Wall Line Count works. Infill Line Directions is just ignored.

    By shoe,
    • 3 replies
    • 140 views

  8. Dividing a Large Print into Several Smaller Prints in cura

    By chrisiiiii,
    • 3 replies
    • 433 views

  9. I cant find my printer on Ultimaker Cura

    By ozzysama,   
    • 4 replies
    • 627 views

  10. Calibration at every shift?

    By MacNobes,
    • 2 replies
    • 97 views

  11. Brim not complete

    By dennis98290,
    • 2 replies
    • 120 views

  12. Tiny holes and gaps on walls and Z seam 1 2

    By neoweiter,
    • 30 replies
    • 4.7k views

  13. Creality Ender 3 V3 SE is not avalible in UltiMaker Cura under add Printer 1 2

    By USY,
    • 45 replies
    • 39.4k views

  14. cura 5.6.0

    By Crotalo,
    • 1 reply
    • 285 views

  15. Cura 5.5 turns off fan for top layers

    By rimbo,
    • 6 replies
    • 306 views

  16. I cannot find my printer in Cura

    By LordVaris,
    • 1 reply
    • 155 views

  17. Cube not thumbnail showing in digital factory

    By Rjndwn,
    • 2 replies
    • 152 views

  18. Ironing end move

    By SensataPDS,
    • 2 replies
    • 124 views

  19. Fan On when printing top layer of infill

    By MrAlvin,   
    • 2 replies
    • 680 views

  20. Is there a way to compare settings side by side?

    By SensataPDS,
    • 3 replies
    • 221 views

  21. select part of model to print last

    By manic101,
    • 2 replies
    • 132 views

  22. CuraEngine - Trying to execute from PYthon Shell....

    By miketrotta,
    • 1 reply
    • 129 views

  23. Ender 3 V3 SE doesn't extrude when using Cura, but does when using Creality Slicer

    By MOCCOR,
    • 1 reply
    • 1.1k views

  24. wall / Layer offset in surface mode

    By neillymackers,
    • 3 replies
    • 214 views

  25. UltiMaker Cura 5.6 beta released

    By ArunC,
    • 18 replies
    • 2.9k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...