Coffee corner

2,049 topics in this forum

1. Ultimaker S5 Launch Event in Amsterdam

   By dianaluchin, May 14, 2018
   • 0 replies
   • 1,505 views
   • 
   • dianaluchin
   • May 14, 2018

2. Transparent Aluminium

   By Brulti, May 2, 2018
   • 0 replies
   • 603 views
   • 
   • Brulti
   • May 2, 2018

3. Ultimaker 4, The next generation of 3d printer 1 2 3 4 5

   By Troki, November 9, 2017   

   • GOSSIP
   • REQUEST
   • 116 replies
   • 15,993 views
   • 
   • fergazz
   • April 21, 2018

4. Polymaker Polybox?

   By cdrose, March 8, 2018
   • 19 replies
   • 2,460 views
   • 
   • kmanstudios
   • April 20, 2018

5. Any Ultimaker community members here heading to Solidworks World next week?

   By mattgriffin, February 3, 2017
   • 1 reply
   • 2,127 views
   • 
   • MikeZ
   • April 16, 2018

6. Trying out fuzzy skin---fun to watch :)

   By kmanstudios, April 12, 2018
   • 0 replies
   • 642 views
   • 
   • kmanstudios
   • April 12, 2018

7. Monoprice mini select V2 print screen

   By Bobbymonte, April 7, 2018   

   • HELP
   • 0 replies
   • 607 views
   • 
   • Bobbymonte
   • April 7, 2018

8. New to 3D printing

   By Coalwater, March 27, 2018
   • 0 replies
   • 582 views
   • 
   • Coalwater
   • March 27, 2018

9. Not 3D printing, but very important to me

   By kmanstudios, March 23, 2018
   • 6 replies
   • 634 views
   • 
   • kmanstudios
   • March 26, 2018

10. Howdy

    By Ianmark, March 24, 2018
    • 1 reply
    • 609 views
    • 
    • SandervG
    • March 26, 2018

11. MRRF / Midwest RepRap Festival 2018

    By fergazz, March 5, 2018
    • 2 replies
    • 1,286 views
    • 
    • gr5
    • March 6, 2018

12. advice for help

    By rebekah_harper, January 15, 2018
    • 14 replies
    • 959 views
    • 
    • Swissengineer
    • February 21, 2018

13. Little introduction

    By Dragon2781, February 16, 2018   

    • Hi
    • 12 replies
    • 891 views
    • 
    • gr5
    • February 16, 2018

14. question about scaling an object inside cura 3.1

    By grue, February 9, 2018   

    • HELP
    • 6 replies
    • 702 views
    • 
    • kmanstudios
    • February 16, 2018

15. Ultimaker - does management listen to users?

    By twiereng, February 11, 2018   

    • Hi
    • 2 replies
    • 731 views
    • 
    • ahoeben
    • February 14, 2018

16. Announcing the arrival of a brand new, bouncing baby printer

    By kmanstudios, January 24, 2018
    • 0 replies
    • 712 views
    • 
    • kmanstudios
    • January 24, 2018

17. MakerBot Replicator+

    By KindaichiShota, January 11, 2018
    • 3 replies
    • 1,101 views
    • 
    • KindaichiShota
    • January 18, 2018

18. Hello Folks!

    By druckpunkt3d, December 2, 2017   

    • Hi
    • 7 replies
    • 882 views
    • 
    • kmanstudios
    • January 17, 2018

19. Sometimes you see something so cute.....

    By kmanstudios, January 17, 2018
    • 0 replies
    • 590 views
    • 
    • kmanstudios
    • January 17, 2018

20. The great shrink!

    By Clancey, October 18, 2017
    • 5 replies
    • 1,258 views
    • 
    • phuot4phuong
    • January 11, 2018

21. Hello There!

    By kcel, January 6, 2018
    • 2 replies
    • 877 views
    • 
    • kcel
    • January 10, 2018

22. I know I print a lot, but.....

    By Job_van_gennip, January 9, 2018
    • 4 replies
    • 918 views
    • 
    • kmanstudios
    • January 9, 2018

23. Thank you for a wonderful 2017! Ready for 2018?

    By SandervG, January 2, 2018
    • 9 replies
    • 815 views
    • 
    • kmanstudios
    • January 3, 2018

24. 3D Printmaker Exhibit Opportunity--Layers: The Evolving Art of 3D Printing

    By The Festival of Arts, December 29, 2017
    • 0 replies
    • 1,177 views
    • 
    • The Festival of Arts
    • December 29, 2017

25. Speed between differing machines.

    By Clancey, December 23, 2017
    • 3 replies
    • 793 views
    • 
    • ultiarjan
    • December 28, 2017