Jump to content

Improve your 3D prints

Help, tips & tricks

5,364 topics in this forum

  1. Layers don't stick well in small areas.

    By alessandro25,   
    • 0 replies
    • 234 views

  2. how do I change start point of wall/layer ?

    By Kunal_Panchal,   
    • 0 replies
    • 403 views

  3. PVA becomes dirty when dissolving

    By OscarLoddesol,
    • 3 replies
    • 386 views

  4. Brown spots after dissolving PVA material

    By Lodden,   
    • 0 replies
    • 243 views

  5. Cura problem with red surface?

    By Stinus,
    • 12 replies
    • 68.5k views

  6. First layer gaps and other odd issues

    By jeepin95,
    • 2 replies
    • 407 views

  7. Cura not slicing Holes.

    By rodcoronadoh,   
    • 18 replies
    • 3.6k views

  8. Cura gcode problems

    By DaveShed,
    • 3 replies
    • 685 views

  9. printing improvement inquiries

    By YenJiWai,
    • 1 reply
    • 278 views

  10. [PET & PLA] Strong stringing & grainy texture from 180° up to 225°

    By ShivaHaze,
    • 0 replies
    • 276 views

  11. UM3 Heat Creep on Filament causing seizing

    By polygonfuture,
    • 3 replies
    • 366 views

  12. Print fails on one side

    By Naturyev,
    • 1 reply
    • 334 views

  13. Cura bug? Extruder skip from infill going over and over itself multiple times

    By rat_tech,
    • 8 replies
    • 811 views

  14. Problems with overhangs

    By Sparky80,   
    • 0 replies
    • 425 views

  15. Ultimaker S5 0.25 core help

    By jeffreysanten,   
    • 1 reply
    • 339 views

  16. Question about Hotend cooling

    By Igi82m,
    • 8 replies
    • 780 views

  17. Model not watertight - struggling to remedy

    By TheJellyBaby,
    • 4 replies
    • 1.1k views

  18. "Printing holes" makes the model fragile

    By HQmacpro,
    • 3 replies
    • 288 views

  19. Question about embossed printing

    By enitrami,
    • 3 replies
    • 330 views

  20. Lines on surface out of solutions does the same on 2 diferent printers

    By nullifieruk,
    • 0 replies
    • 244 views

  21. Just installed Cura and have one small hiccup when trying to slice and wondering if anyone has experienced this?

    By DavidAlexander,
    • 12 replies
    • 378 views

  22. new to 3D

    By ddcocozza,
    • 2 replies
    • 281 views

  23. Print fail using Cura but OK with another slicer.

    By JohnForeman,
    • 4 replies
    • 407 views

  24. Cura cutting off the bottom of my model

    By patfre,   
    • 11 replies
    • 3k views

  25. Tree hits my project

    By Infowire,
    • 1 reply
    • 244 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 7 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...