Jump to content

Improve your 3D prints

Help, tips & tricks

5,366 topics in this forum

  1. Printed object thicker than model

    By Yowan,   
    • 6 replies
    • 1.4k views

  2. Prevent 'ringing' (wobbly surface after sharp corners)

    By peanudt,
    • 23 replies
    • 39.2k views

  3. Extremely hot stepper motors on Ultimaker 3

    By Kylellrc,   
    • 6 replies
    • 2k views

  4. Stubborn BB Core Not coming clean

    By Jeffg1,
    • 11 replies
    • 1.1k views

  5. Material change not working (anymore)

    By Desperate3D,   
    • 12 replies
    • 2.2k views

  6. Top and Bottom surfaces and impossible prints

    By Tilleen,
    • 1 reply
    • 479 views

  7. Filament not sticking anymore. Possible bed warping?

    By Sevione,   
    • 6 replies
    • 1.4k views

  8. UM2: why is my infill so bad and the borders are good?

    By mezger,   
    • 10 replies
    • 1k views

  9. Extruder Temp doesn't match Cura

    By rkehler67,   
    • 2 replies
    • 2.9k views

  10. Cura Connect wiped out

    By jkennard,   
    • 0 replies
    • 420 views

  11. Cura running very slow on my PC

    By nathanswood,   
    • 0 replies
    • 718 views

  12. Need Tips for Improving 0.25mm Prints on UM2+

    By designmaketeach,
    • 1 reply
    • 641 views

  13. UM2+ Underextrusion/not extruding problem

    By Esacronix,   
    • 6 replies
    • 923 views

  14. over extrusion

    By icewave,   
    • 6 replies
    • 2.1k views

  15. Problems All Of A Sudden - Poor Prints

    By TheKrakenWakes,
    • 2 replies
    • 723 views

  16. Weak prints

    By Kendall Baker,
    • 5 replies
    • 3.3k views

  17. Help!

    By harley573,
    • 11 replies
    • 981 views

  18. Bad overhang surface

    By Thomas3dprint,   
    • 5 replies
    • 1.1k views

  19. sd card problem

    By Dr.mechano,   
    • 3 replies
    • 1.5k views

  20. Nozzle Temperature

    By Adithya,   
    • 0 replies
    • 512 views

  21. Support structure outside part

    By milkman1974,   
    • 2 replies
    • 1.8k views

  22. Build plate cools down when print starts on Ultimaker 2+

    By Wert,   
    • 3 replies
    • 915 views

  23. Material behind the extruder of UM2, is this normal?

    By mezger,   
    • 4 replies
    • 894 views

  24. Initial Layer Problems - Weird

    By rca3g7,   
    • 1 reply
    • 1.2k views

  25. Very low temperature needed

    By mowijo,   
    • 3 replies
    • 705 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...