Improve your 3D prints

5,366 topics in this forum

1. Gaps in circles

   By 3dnerd, November 12, 2021   

   • UM2+
   • 12 replies
   • 2k views
   • 
   • gr5
   • February 15

2. PETG printing problems

   By Corrado1, February 12   

   • PETG
   • Stringing
   • 2 replies
   • 159 views
   • 
   • Corrado1
   • February 14

3. 1.0mm nozzle odd top/bottom shrinking

   By jaysenodell, February 11
   • 19 replies
   • 284 views
   • 
   • Slashee_the_Cow
   • February 14

4. Wall thickness change after Z seam

   By stevewhite, February 12
   • 4 replies
   • 135 views
   • 
   • stevewhite
   • February 13

5. Advice requested - Will this print?

   By glen4cindy, February 10
   • 8 replies
   • 181 views
   • 
   • jaysenodell
   • February 13

6. Even/Odd Slicing Mode ? For lightweight PLA : drones/rc planes

   By mscir, February 13
   • 2 replies
   • 154 views
   • 
   • mscir
   • February 13

7. Best fast but good quality settings

   By Simonsrk, February 12   

   • Cura
   • settings
   • (and 2 more)

     Tagged with:

     • Cura
     • settings
     • fast
     • quality
   • 1 reply
   • 224 views
   • 
   • Slashee_the_Cow
   • February 13

8. Little Blister Issue?

   By MikeTX, February 12
   • 1 reply
   • 91 views
   • 
   • MikeTX
   • February 12

9. Managing GCode vs 3mf

   By jaysenodell, February 11
   • 2 replies
   • 142 views
   • 
   • jaysenodell
   • February 12

10. Good layer, Bad layer

    By aaron81006, January 26
    • 7 replies
    • 227 views
    • 
    • Slashee_the_Cow
    • February 12

11. Weird porous wall defects on 3D prints

    By Arthpatel9497, February 5   

    • Walls
    • Porous
    • (and 5 more)

      Tagged with:

      • Walls
      • Porous
      • Porous walls
      • Porosity defect
      • Thin wall defects
      • Wavy wall defects
      • Wavy thin walls
    • 3 replies
    • 188 views
    • 
    • Slashee_the_Cow
    • February 11

12. empty spaces at the bottom

    By Corrado1, February 7   

    • bottom layer
    • 4 replies
    • 182 views
    • 
    • Slashee_the_Cow
    • February 9

13. Bad print results

    By Biem1000, February 4
    • 4 replies
    • 233 views
    • 
    • gr5
    • February 7

14. Easier support removal

    By jaysenodell, February 6
    • 7 replies
    • 528 views
    • 
    • jaysenodell
    • February 7

15. FEATURE REQUIRED: DIFFERENT LINE WIDTH FOR BOTTOM SKIN

    By centunesima, February 6
    • 3 replies
    • 135 views
    • 
    • Slashee_the_Cow
    • February 6

16. Spider webs from hades… or excess pla stinginess

    By jaysenodell, February 2
    • 6 replies
    • 176 views
    • 
    • Slashee_the_Cow
    • February 6

17. Traffic Cone 1:8 Print - strange slicer behavior

    By kerezst, February 5
    • 1 reply
    • 111 views
    • 
    • Slashee_the_Cow
    • February 5

18. I have a question about my ender 3 printing

    By dave1956, January 15
    • 5 replies
    • 165 views
    • 
    • Carlbosson
    • February 5

19. Arrêt de l'extrusion à 98% d'impression quelque soit l'objet

    By Mamou, February 1
    • 1 reply
    • 155 views
    • 
    • Slashee_the_Cow
    • February 3

20. Problem with a print / stringing with small figures / bed adhesion? Picture below

    By Sallyx1, February 1
    • 1 reply
    • 96 views
    • 
    • GregValiant
    • February 1

21. Sporadic layer height changes during print

    By rkondakjian, January 31
    • 1 reply
    • 114 views
    • 
    • rkondakjian
    • January 31

22. Noob mind boggled with slicing STL vs G-code file not printing same quality.

    By Mr_Stark1981, January 20   

    • G-code
    • layers
    • (and 2 more)

      Tagged with:

      • G-code
      • layers
      • Stringing
      • Supports
    • 17 replies
    • 321 views
    • 
    • Slashee_the_Cow
    • January 29

23. weird rough patch on ball

    By greenieboy, January 21
    • 15 replies
    • 371 views
    • 
    • Slashee_the_Cow
    • January 27

24. Ultimaker 5S first layers running rough.

    By Yoniweb, January 26
    • 3 replies
    • 145 views
    • 
    • Yoniweb
    • January 26

25. New Printer Stringy PVA 1 2

    By dandeluca, January 8
    • 25 replies
    • 817 views
    • 
    • Slashee_the_Cow
    • January 23