Jump to content

Deutsch

Herzlich willkommen im deutschsprachigen Forum

3,184 topics in this forum

  1. löchrige Oberfläche

    By oxoTURULoxo,
    • 11 replies
    • 1k views

  2. Thingiverse - kein Konto-Zugriff mehr

    By ManAtArms,
    • 6 replies
    • 1.2k views

  3. Cura legt Druckobjekt einfach auf Druckfläche ab

    By Mala_Fide,
    • 3 replies
    • 428 views

  4. Ultimaker upgrade

    By Allrounder,
    • 10 replies
    • 604 views

  5. Nach 5mm Bauhöhe kein Material mehr

    By fofa,
    • 6 replies
    • 487 views

  6. S7 Bedlevel, Bauraumtemperatur

    By TheM3chanic,
    • 5 replies
    • 508 views

  7. LED leuchtet bei Druck, schaltet ab wenn er fertig ist, kann das verzögert passieren?

    By Filmpalast,
    • 3 replies
    • 370 views

  8. Distanzproblem UM2+

    By ManAtArms,   
    • 3 replies
    • 446 views

  9. Filament wird nicht erkannt

    By kathi113,
    • 1 reply
    • 469 views

  10. Materialfehler während des Druckjobs S5

    By PKlemm,
    • 2 replies
    • 677 views

  11. UM S5 mit Materialstation - permanent Fehler Er58 Fehler bei Verbindung von Materialladefach

    By schmierfink,   
    • 0 replies
    • 485 views

  12. Cura will immernoch in die Luft drucken...

    By Odracir1978,   
    • 15 replies
    • 1.9k views

  13. Kann in Cura 5.3.1 Support Interface nicht wieder abschalten

    By kalle_wirsch,
    • 0 replies
    • 455 views

  14. Bowden für UM2

    By Falko,
    • 15 replies
    • 796 views

  15. Zusammenarbeit mit Fusion360 geht nicht mehr

    By ohawd,
    • 20 replies
    • 1.2k views

  16. Cura 5.3.1

    By michaelapp,
    • 1 reply
    • 866 views

  17. Cura 5.3.1 Probleme mit Raft

    By AliveAgain,   
    • 3 replies
    • 574 views

  18. Sovol SV04 lässt sich nicht einbinden.

    By Abraxas71,   
    • 2 replies
    • 558 views

  19. Fläche ohne Wandstärke drucken

    By Produktdesigner,
    • 0 replies
    • 384 views

  20. Ultimaker S7 im lokalen Netzwerk nicht erreichbar

    By cdr-automatisierung,
    • 7 replies
    • 817 views

  21. Farben der Druckköpfe

    By cdr-automatisierung,
    • 3 replies
    • 584 views

  22. Wie kann ich den namen des Druckers ändern?

    By luc_vienna,   
    • 0 replies
    • 893 views

  23. Problem mit mehreren aktiven Ultimaker-Druckern in Cura

    By HoAlb,
    • 2 replies
    • 497 views

  24. Extruder 1 druckt teilweise "in die Luft"

    By ASwoboda,
    • 8 replies
    • 714 views

  25. Menü oben wird nicht angezeigt

    By cdr-automatisierung,
    • 2 replies
    • 448 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...