Deutsch

3,103 topics in this forum

1. UM2 - MK7 Gear - Flow oder Filamentdurchmesser anpassen?

   By oceanblue72, November 7, 2015
   • 1 reply
   • 1.5k views
   • 
   • martin-hillenbrand
   • November 14, 2015

2. Bevor ich mir einen UM Original+ kaufe habe ich noch ein paar Dinge zu klähren, dualextrusion(notwendig/machbar)?

   By ABurkandt8519, November 5, 2015
   • 4 replies
   • 1.8k views
   • 
   • ABurkandt8519
   • November 9, 2015

3. Fehlerhafter Drucker immer in gleicher Höhe

   By markusmaker, June 15, 2015
   • 6 replies
   • 3.3k views
   • 
   • markusmaker
   • November 5, 2015

4. Gewährleistung nur von Ultimaker ? Nicht vom Verkäufer ?

   By HannesW, November 3, 2015
   • 1 reply
   • 1.3k views
   • 
   • ULTIMAKER2EXTEND
   • November 3, 2015

5. Fehlerhafter Schichtaufbau

   By Redster, September 24, 2015
   • 2 replies
   • 1.6k views
   • 
   • ULTIMAKER2EXTEND
   • November 3, 2015

6. Ultimaker 2 Extended Unterschiede zentraler Lüfter

   By ULTIMAKER2EXTEND, August 5, 2015
   • 6 replies
   • 2.8k views
   • 
   • ULTIMAKER2EXTEND
   • October 30, 2015

7. Suche gebrauchten UM2 zum Kauf

   By HMarcus, October 29, 2015
   • 1 reply
   • 1.3k views
   • 
   • DidierKlein
   • October 29, 2015

8. Material Flow bei aktueller Cura Firmware zu gering berechnet?

   By DelVantes, October 25, 2015
   • 1 reply
   • 4.8k views
   • 
   • Nicolinux
   • October 28, 2015

9. Welches Filament für Getriebe - Messing auf Kunststoff

   By oceanblue72, October 26, 2015
   • 2 replies
   • 1.5k views
   • 
   • oceanblue72
   • October 26, 2015

10. Gebrauchter Ultimaker 2

    By Blueforcer, October 22, 2015
    • 1 reply
    • 2k views
    • 
    • 3d4you
    • October 26, 2015

11. Geschlossen - Sammelbestellung UM2 Präzisions- Alu PEI Dauerdruckplatte Maße: 5mm x 257x229mm 1 2 3 4 5

    By martin-hillenbrand, January 23, 2015
    • 108 replies
    • 18.1k views
    • 
    • martin-hillenbrand
    • October 21, 2015

12. Daten aus Shop für Architekten / CAD

    By LisaMariaH, October 20, 2015
    • 1 reply
    • 1.4k views
    • 
    • 3Dimensionen
    • October 21, 2015

13. Problem beim drucken ...

    By stoque, October 18, 2015
    • 6 replies
    • 1.9k views
    • 
    • stoque
    • October 19, 2015

14. 3D Druck in Stuttgart - Milaneo

    By ndimensional, November 29, 2014
    • 5 replies
    • 5.1k views
    • 
    • MakeIT
    • October 19, 2015

15. Verkaufe 2 x colorFabb PLA/PHA *NEU

    By D-ALPA, September 22, 2015
    • 1 reply
    • 1.4k views
    • 
    • backinblack81
    • October 18, 2015

16. Feeder skipping (mal wieder) 1 2

    By xperiment, September 2, 2015
    • 26 replies
    • 5.8k views
    • 
    • backinblack81
    • October 18, 2015

17. Verkaufe UM2 mit viel Filament und Rechnung

    By budschinger, September 18, 2015
    • 3 replies
    • 1.8k views
    • 
    • stoque
    • October 18, 2015

18. Ultimaker 2 - seitlicher Lüfter läuft nicht

    By taires, February 27, 2014
    • 11 replies
    • 4.2k views
    • 
    • GolaxR6
    • October 15, 2015

19. ABS Natural 2.85 mm zu verkaufen

    By backinblack81, October 15, 2015
    • 0 replies
    • 1.4k views
    • 
    • backinblack81
    • October 15, 2015

20. Wie schnell druckt Ihr mit 3mm ABS.

    By martin-hillenbrand, October 3, 2015
    • 2 replies
    • 2k views
    • 
    • martin-hillenbrand
    • October 12, 2015

21. z-achse auf null stellen ?!

    By Basti2502, October 4, 2015
    • 0 replies
    • 2.1k views
    • 
    • Basti2502
    • October 4, 2015

22. Lüfter Tuning

    By darkx88, September 17, 2014
    • 16 replies
    • 5.9k views
    • 
    • ThomasBe
    • September 30, 2015

23. Lautstärke

    By ThomasBe, September 24, 2015
    • 3 replies
    • 3.4k views
    • 
    • oceanblue72
    • September 30, 2015

24. Gcode (Ulticode) zu Modell

    By tobiasmueller94, September 14, 2015
    • 1 reply
    • 2.3k views
    • 
    • ThomasBe
    • September 29, 2015

25. Suche gebrauchten Ultimaker 2

    By donandi, July 31, 2015
    • 5 replies
    • 1.7k views
    • 
    • 3Dimensionen
    • September 28, 2015