Deutsch

3,103 topics in this forum

1. Doppelextruder möglich?

   By blacklion83, July 18, 2013
   • 12 replies
   • 2.9k views
   • 
   • vanharry
   • August 15, 2013

2. Kit oder zusammengebaute Ausführung?

   By sacad, August 4, 2013
   • 12 replies
   • 2.5k views
   • 
   • thingster
   • August 15, 2013

3. Material Nachschub

   By aaren-san, June 9, 2013
   • 10 replies
   • 7.4k views
   • 
   • vanharry
   • August 8, 2013

4. Ultimaker beizen?

   By znib, June 13, 2013
   • 7 replies
   • 2.3k views
   • 
   • vanharry
   • August 8, 2013

5. Torx Schrauben auftreiben

   By Nicolinux, July 29, 2013
   • 4 replies
   • 2.2k views
   • 
   • Nicolinux
   • July 30, 2013

6. UltiController Display nicht beleuchtet?!

   By flashback, May 11, 2013
   • 6 replies
   • 2.5k views
   • 
   • jonnybischof
   • July 30, 2013

7. Kaufberatung

   By alain, June 28, 2013
   • 7 replies
   • 3.9k views
   • 
   • burki
   • July 22, 2013

8. Laywoo-D3

   By aaren-san, June 11, 2013
   • 2 replies
   • 2.9k views
   • 
   • maker
   • July 20, 2013

9. Ultimaker in Magdeburg

   By partofthecurse, May 12, 2013
   • 2 replies
   • 1.9k views
   • 
   • maker
   • July 20, 2013

10. Einstellungen oder G-Code ändern?

    By ulbie, July 6, 2013
    • 5 replies
    • 13.3k views
    • 
    • ulbie
    • July 16, 2013

11. Druckauftrag

    By vanharry, July 15, 2013
    • 2 replies
    • 1.7k views
    • 
    • vanharry
    • July 16, 2013

12. Heater-Block kaputt gegangen, wo gibt es Ersatz?

    By vanharry, July 12, 2013
    • 2 replies
    • 1.6k views
    • 
    • vanharry
    • July 13, 2013

13. Problem mit Hubtisch

    By blacklion83, June 21, 2013
    • 6 replies
    • 2.1k views
    • 
    • thingster
    • July 2, 2013

14. Ultimaker in Dinkelscherben (Augsburg)

    By chri, June 6, 2013
    • 2 replies
    • 1.8k views
    • 
    • chri
    • June 26, 2013

15. Einige Fragen nach UM-Aufbau

    By blacklion83, June 18, 2013
    • 1 reply
    • 1.9k views
    • 
    • thingster
    • June 18, 2013

16. Bischofswiesen ist dabei

    By inskale, May 17, 2013
    • 7 replies
    • 1.9k views
    • 
    • dberneker
    • June 15, 2013

17. Filament wechseln. Wie?

    By isphording90, March 30, 2013
    • 8 replies
    • 9.6k views
    • 
    • thingster
    • June 11, 2013

18. Doppel-Extruder ab wann?

    By blacklion83, June 10, 2013
    • 0 replies
    • 1.7k views
    • 
    • blacklion83
    • June 10, 2013

19. Bowden Tube rutscht immer raus

    By aaren-san, June 6, 2013
    • 6 replies
    • 3.6k views
    • 
    • aaren-san
    • June 8, 2013

20. Lieferung on Hold

    By aceteam, June 7, 2013
    • 2 replies
    • 1.9k views
    • 
    • chri
    • June 8, 2013

21. Seltsame Rillen

    By aaren-san, June 4, 2013
    • 1 reply
    • 3.1k views
    • 
    • thingster
    • June 6, 2013

22. Fragen zur Bestellung

    By icoo, June 5, 2013
    • 1 reply
    • 1.5k views
    • 
    • thingster
    • June 6, 2013

23. Anleitung: Ansprühen eures Ultimakers

    By plasmasolutions, May 19, 2013
    • 3 replies
    • 2k views
    • 
    • thingster
    • June 5, 2013

24. Sollte der Lüfter nicht anlaufen?

    By csdragon, May 9, 2013
    • 7 replies
    • 2.4k views
    • 
    • goodwell
    • May 28, 2013

25. Verschiebung bei jedem Layerwechsel in die X und! Y Achse

    By sandymaker, May 17, 2013
    • 5 replies
    • 3.1k views
    • 
    • goodwell
    • May 28, 2013