Jump to content

Deutsch

Herzlich willkommen im deutschsprachigen Forum

3,184 topics in this forum

  1. Building Plate Leveling - Druckkopf nimmt 3. Position nicht ein

    By Kruemel97,   
    • 0 replies
    • 123 views

  2. Z Abstand Stützstruktur

    By PeaveyMcear,
    • 2 replies
    • 288 views

  3. Bitte um Hilfe: G-Code ändern - Danke :-)

    By Julucz1988,
    • 12 replies
    • 451 views

  4. Fläche eines zusammengesetzte Modelles auf Druckbett setzen

    By Felsentreu,
    • 13 replies
    • 276 views

  5. Objekt wird nicht richtig Gesliced

    By Shakari,
    • 3 replies
    • 410 views

  6. Erste Schicht hat große Lücken

    By TheRealHarpi,   
    • 4 replies
    • 943 views

  7. Geräusche in der X-Achse beim Ultimaker S3 1 2 3

    By Gosman,   
    • 72 replies
    • 5.3k views

  8. Probleme mit Handling von Profilen. Bitte um Erleuchtung

    By 11102022,
    • 3 replies
    • 255 views

  9. Hilfe: Geht das überhaupt? Gesamter Druckprozess anzeigen

    By Ghost_Morien_yt,
    • 1 reply
    • 140 views

  10. Wie kann man Unerwünschte zusätzliche schichten an schrägen abstellen? Siehe Bild!

    By Vin83,
    • 3 replies
    • 302 views

  11. Erster Druck mit PVA Stringing und Krümel normal ?

    By Masterdark,
    • 5 replies
    • 551 views

  12. Drucken über das Internet geht nicht weg. Materialeinstellungen

    By Kherz,
    • 3 replies
    • 357 views

  13. Fehlermeldung an Ultimaker2+ connect : File format incorrect

    By Kherz,
    • 0 replies
    • 116 views

  14. UM S7 Überhänge Problem

    By AlexanderInnocente,
    • 9 replies
    • 507 views

  15. Pausieren nach Positionierung

    By PeaveyMcear,
    • 4 replies
    • 194 views

  16. Luftleitung im Inneren des Bauteils

    By Koch_SAXONIA,
    • 2 replies
    • 206 views

  17. Z-Naht auf Objektvorderseite verbergen

    By spodec90,   
    • 3 replies
    • 607 views

  18. Schrumpfung

    By Allrounder,
    • 11 replies
    • 592 views

  19. VOC Emissionen vom 3D Druck

    By zpm3atlantis,   
    • 9 replies
    • 705 views

  20. Ultimaker S3 X/Y Duckgenauigkeit 1 2

    By Masterdark,   
    • 25 replies
    • 929 views

  21. Speichern auf SD-Card

    By Achi1961,
    • 2 replies
    • 328 views

  22. S7/Cura: Kreise sauber drucken nicht möglich

    By AlexanderInnocente,
    • 18 replies
    • 1.1k views

  23. Projektdatei (.3mf) öffnet nicht mit Cura Einstellungen

    By tobiac,
    • 1 reply
    • 542 views

  24. Ultimaker S3 Cura 5.5 Temp Tower drucken funktioniert nicht richtig

    By Masterdark,   
    • 2 replies
    • 397 views

  25. Dichte der Dachstruktur

    By walair,
    • 5 replies
    • 275 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...