Español

284 topics in this forum

1. problema soportes

   By berto85, May 11
   • 5 replies
   • 759 views
   • 
   • Chrixt
   • August 29

2. Telaranas en mis impreciones

   By Oarias, August 20
   • 0 replies
   • 121 views
   • 
   • Oarias
   • August 20

3. Hola buenos días a todos. Tengo varias versiones de Cura y en todas me aparece el mismo problema que no sé como solucionarlo.

   By gustavo_gac, August 8
   • 2 replies
   • 238 views
   • 
   • gustavo_gac
   • August 8

4. Mi ultimaker 2 extended+ parece tener una falla

   By nkgonn, July 18
   • 0 replies
   • 186 views
   • 
   • nkgonn
   • July 18

5. ultimaker cura no responde

   By vanruso73, June 28, 2023
   • 2 replies
   • 1.2k views
   • 
   • Slashee_the_Cow
   • July 11

6. Cómo imprimo mediante USB a ultimaker 2 extended+?

   By nkgonn, July 1
   • 1 reply
   • 243 views
   • 
   • Dustin
   • July 1

7. PROBLEMA

   By CAPRICORNIO, June 21
   • 1 reply
   • 186 views
   • 
   • GregValiant
   • June 21

8. modo de impresión MAKERBOT

   By damoont, June 12
   • 0 replies
   • 225 views
   • 
   • damoont
   • June 12

9. Generación manual de soportes

   By gustavo_gac, May 21
   • 0 replies
   • 400 views
   • 
   • gustavo_gac
   • May 21

10. El tiempo de segmentacion inferior al real

    By Diego0811, May 16
    • 0 replies
    • 173 views
    • 
    • Diego0811
    • May 16

11. pequeños agujeros

    By berto85, May 14
    • 0 replies
    • 171 views
    • 
    • berto85
    • May 14

12. dudas calidad figuras

    By berto85, May 13
    • 0 replies
    • 159 views
    • 
    • berto85
    • May 13

13. Hola, cómo hago para imprimir directamente desde mi pc a mi witbox?

    By emili, May 1
    • 0 replies
    • 281 views
    • 
    • emili
    • May 1

14. Impresion terminada pero realmente no....

    By udivicino, April 18
    • 0 replies
    • 250 views
    • 
    • udivicino
    • April 18

15. Problemas con Cura 5.5 y gcode

    By Nacho2014, November 8, 2023
    • 3 replies
    • 719 views
    • 
    • Kidrev
    • April 9

16. Perdí la configuración de cura

    By delwin, April 2
    • 0 replies
    • 291 views
    • 
    • delwin
    • April 2

17. Ayudaaaa porfisss

    By silviaMH, March 14
    • 2 replies
    • 445 views
    • 
    • Slashee_the_Cow
    • March 15

18. Gcode Impresion misma capa 2 colores

    By Matferrari, March 2
    • 1 reply
    • 652 views
    • 
    • GregValiant
    • March 2

19. Presentacion

    By Matferrari, March 2
    • 0 replies
    • 179 views
    • 
    • Matferrari
    • March 2

20. Problema para arrastrar archivos

    By edsuce, February 13
    • 0 replies
    • 268 views
    • 
    • edsuce
    • February 13

21. Imprimir con cable desde PC

    By ACasas, February 5
    • 1 reply
    • 302 views
    • 
    • Dustin
    • February 5

22. ender 3

    By yone84, December 31, 2023
    • 1 reply
    • 422 views
    • 
    • ram7255
    • January 16

23. Mis diseños siempre se imprimen en una esquina y no sirven

    By marcoagac, March 25, 2023
    • 3 replies
    • 1.9k views
    • 
    • anuevalo
    • January 5

24. Ensamblar dos gcode ¿se puede?

    By ram7255, December 19, 2023
    • 1 reply
    • 378 views
    • 
    • ram7255
    • December 20, 2023

25. los iconos de escalar y de rotar no aparecen en la pantalla. Mi vercion es la 5.6 de cura

    By narbel500, December 17, 2023
    • 0 replies
    • 247 views
    • 
    • narbel500
    • December 17, 2023