Jump to content
Ultimaker Community of 3D Printing Experts

Leaderboard

Popular Content

Showing content with the highest reputation since 04/20/2015 in 3D Print

  1. Version 1.0.0

    315 downloads

    Here is my full size Velociraptor skeleton. Juste made for the challenge. Lenght: ~180cm Sculpted with Zbrush. Total printing time: ~392h. Printer: Ultimaker2+ Filament: PLA Speed: 30mm/s - 50mm/s Nozzle: 0,4mm Layers: 0,15mm Painting : acrylic paint (spray and brushe)
    22 points
  2. Version 1.0

    9,687 downloads

    The original dodecahedral kinetic sculpture by Stijn van der Linden a.k.a. Virtox. Made of five nested dodecahedra, each one is limited to rotate around its own axis. It was printed with dual extrusion on an Ultimaker 3 with water-soluble PVA support material.
    11 points
  3. Version 1.0.0

    73 downloads

    1/40 Mosasaurus Nozzle : 0.4 Layer : 0.06
    9 points
  4. Version 1.0.0

    87 downloads

    Nozzle : 0.4 Layer : 0.06 #dinosaur #giganotosaurus #dino #dinosaurs #figure
    7 points
  5. Version 1.0

    2,890 downloads

    During my spell working in the Art department on 'Avengers Age of Ultron' I was asked by the production designer to build a prop to help dress the interior set of 'Stark Towers' The model was to show the new section of tower that replaced the damaged section from the original film. As I only had 4 weeks to build it (including 3d modelling) we needed to simplify the design a bit, hence the lower portion being in laser cut acrylic. Using my trusty Ultimakers I think I pulled off the desired effect, even if it only appeared in the movie for less than a second!
    7 points
  6. Version 1.0

    498 downloads

    Star Wars Porg!
    7 points
  7. Version 1.0

    5,702 downloads

    This is a well known vase printed in Blue Lagoon from Faberdashery (very nice). It's printed with my Ultimaker 2 modified with the Olsson Block and a 1mm nozzle from www.3dSolex.com. Printed in Spiralize mode with a 1mm wall, and 0.5mm layers! It's very fast, around 1h25 to print at full height (200mm). Watch the video! I'll do a complete review soon on this nozzle
    7 points
  8. Version 1.0

    160 downloads

    T-Rex Skull
    6 points
  9. Version 1.0

    2,277 downloads

    Boon, The Tiny T-Rex from 3DKitbash
    5 points
  10. Version 1.0

    5,241 downloads

    promo toy for Russian company REC
    5 points
  11. Version 1.0.0

    35 downloads

    This is a suggestion to develop a new type of support that gows from the side of the printed part instead of the print bed. This could reduce material used for support and reduce print time. I have done two tests to compare, the design can be improved and i am sure a slincing algorythm can be added maybe in "Cura" to have Ramification support. I added Pictures and the models of two comparative parts. Let me know what you think and if you can develop the algorythm. This is totally open source suggestion i claim no right for. I only would like it to be named "Ramificaitons".
    5 points
  12. Version 1.0.0

    106 downloads

    My special designed filament holder are directly for the original ULTIMAKER 3 (UM3) spools. Until now I use it for the 350g and 750g spools of 2.85mm filament (see pictures). Advantages: Easy to clamp or unloose in the spool Best way of storing the filament spools Spools are better stackable No unraveling of the filament End of filament doesn't have to be fixed in the small hole and the danger of breaking filament I'm looking forward to your feedback and especially if it works as well for the other material spools. Have fun. Posted at h
    5 points
  13. Version 1.0.0

    348 downloads

    elegant swinging smartphone stand The idea was a smartphone stand, where you have the ability to connect your standard charging cable... ... and then inspiration began to flow...
    4 points
  14. Version 1.0

    330 downloads

    Why another phone dock? The new iPhone X is a few mm taller than the previous phones, so my old printed iPhone dock didn't work anymore. After some browsing I could not find any other dock I liked. The one I liked that doesn't fit does not exist for the X and I dislike mods on STLs/OBJs. The generic ones are typically clumsy or have other issues. So I decided to design one quickly from scratch. Here's the result I would like to share. I think there are not enough phone docks out there yet! :-)
    4 points
  15. Version 1.0

    5,777 downloads

    To improve the CNC Router and not just to drill stuff, I also wanted to cut materials like cardboard, vinyl, paper, etc. Before to buy a lasercut, I did find in Internet a very interesting tool to transform the Spindle into a cutting machine. I wanted to buy the knife tool, but my spindle collet is 8mm, and most of the tools I saw doesn´t fit on it, so I decide to make my own, and after some failed prototypes and test, I made one that until now, after several test it works just great!. The blade can be coupled in two different positions, with a cut depth of 6mm or 10mm. Component list
    4 points
  16. Version 1.0

    2,088 downloads

    I'm a huge Ghostbusters fan, and wen the board game came out, it included about 100 amazing figures.. but there were a few things lacking, so I decided to make them myself! First I did the slime splats you see pictured, modelled in zbrush. The big project though, was a dice tower based on the Ghostbusters firehouse. The game's figures are based off the comic book artwork, so I decided to do a toon version of the firehouse, based on the old saturday morning cartoon. Learning how a dice tower works, and printing a rough draft version really helped in the design of this. This like the ramps an
    3 points
  17. Version 1.0.0

    76 downloads

    After searching the net again and again, I did not found a nice Dom Tower variant to print. So I decided to create my own versions: Single piece version (20 cm tall) Duplo compatible (big colored one, 53 cm tall) Lego compatible (PLA brons fill & Glow in the dark) Christmas edition (PLA silver, optional having 3 electric candles inside) Unfortunately the electric candles are still somewhere in China so I'm still curious how this will look like.. Stl file could be found here: https://cults3d.com/en/3d-model/architecture/dom-tower-utrecht (Sin
    3 points
  18. Version 1.0

    611 downloads

    To be able to better control the temperature inside the Ultimaker 3 I created this simple front door. It is based upon a 3mm acrylic glass plate (size 325 x 325 mm2) and two top hooks, a handle and a bottom hook. The parts need to be glued together with a suitable plastic glue. During printing the door covers the front side of the UM3. If not needed, it can be hung at one of the printer sidewalls. The basic design should fit the UM2 also, but I'm not sure about the wall thickness, which seems to be different between the UM3 and UM2.
    3 points
  19. Version 1.0

    452 downloads

    For everyone who want to have keychain with Ultimaker Follow me on Facebook : https://www.facebook.com/alen.kuhta/media_set?set=a.971249112929474.1073741827.100001331847671&type=3&pnref=story and Twitter : https://twitter.com/a_kuhta Thank you.
    3 points
  20. Version 1.0

    805 downloads

    Fort Boyard
    3 points
  21. Version 1.0

    1,600 downloads

    Functional low-cost photogrammetry 3D scanner, entirely built with the Ultimaker, the chassis split into four parts and finished with epoxy resin.
    3 points
  22. Version 1.0

    7,355 downloads

    This Vertical Axis Wind Turbine (VAWT) was made by @Valcrow for the new Ultimaker 2+. To make it yourself you can visit YouMagine to download the files and our Wind Turbine print tutorial for print/assembly tips. The Ultimaker 2+ desktop 3D printer is based on the award-winning Ultimaker 2 and features all of our latest innovations and understanding of 3D printing.
    2 points
  23. Version 1.0.0

    85 downloads

    We would like to share with you a 3D printable, build-it-yourself decoration to bring fun and joy when and where it matters this Christmas. Special thanks to our community member @flowalistik for creating this model!
    2 points
  24. Version 1.0

    2,165 downloads

    Endo the 3D printed Action Figure
    2 points
  25. Version 1.0

    1,121 downloads

    Time to move on, enough Pokémons printed for friends Instagram post here!
    2 points
  26. Version 1.0

    673 downloads

    they show your guests where the toilet is...
    2 points
  27. Version 1.0

    918 downloads

    It is a spare part of a Philips Hair Clipper !
    2 points
  28. Version 1.0

    5,632 downloads

    Ever wanted to know what makes the Ultimaker robot tick? I was inspired by illustrations such as this one: http://altjapan.typepad.com/.a/6a00d8341bfd2253ef014e8936f006970d-pi The "maker globe" was created using a NASA satellite image maps of lights on the earth at night in order to generate the gears. I assumed that the brighter areas on the map would have a greater density of Makers, so there are more gears populating those areas on the globe. The lines in the oceans were derived from images of shipping lanes. I wanted to distill the idea of Makers working together and ideas traveling
    2 points
  29. Version 1.0.0

    43 downloads

    Design by @lekid Inspired by a picture found on internet Printed with Polymaker Polysmooth filament and polished with the Polysher Then glued on a glass frame of 30cm x 60cm
    2 points
  30. Version 1.0.0

    13 downloads

    Hi there, I designed a little dual colour print for christmas Print files Merry Christmas
    2 points
  31. Version 1.0

    1,716 downloads

    Ultibot head toilet roll holder
    2 points
  32. Version 1.0

    885 downloads

    Projet perso : un voilier de class "Footy" d'après un plan de Claudio Vigada (Italie) à l'origine conçu pour être réalisé en depron. La coque a été entièrement dessinée sous 123D Design (RIP). Elle est entièrement creuse : les parois font 0.62 mm. Elle est en deux parties assemblées à l'epoxy au niveau du puits de dérive. La dérive est démontable. Elle embarque un lest en plomb de 310 gr caché dans deux demi coquilles imprimées elles aussi. La platine radio est en deux parties : les servos sont maintenus en place par emboitement. Seules les têtes de servos dépassent. La trappe sera ferm
    2 points
  33. Version 1.0

    530 downloads

    Printed in Extrudr GreenTec on my "GudoMaker" (heavily modded UMO+). No painting, only matte clear coating after some light sanding.
    2 points
  34. Version 1.0

    374 downloads

    Printed in Extrudr Greentec on a modded UMO+. The model was scaled down to 70% to fit on our doors. Slightly sanded and painted with matte clear coating.
    2 points
  35. Version 1.0

    763 downloads

    Printed in 3 parts. Hight: 340mm Diam: 120mm
    2 points
  36. Version 1.0

    498 downloads

    A test sculpt of my friends dog.... still trying to get my UM2 back to spec. Didnt realise the 35W heater needed a PID alteration or something, but hopefully I'll have that sorted and will be back to making near flawless prints. No closeups here because they are not worthy of closeups.
    2 points
  37. Version 1.0

    1,403 downloads

    Impression 3D maquette, surface totale du projet 283 m² 1.5 cm / 1 m dimension maquette 42cm / 43cm / hauteur 9 cm
    2 points
  38. Version 1.0

    5,168 downloads

    I wanted a more integrated solution for mounting a Raspberry Pi Camera on the UM2, so i designed one. I am using a third-party camera module with a 36x36mm board and a M12 lens mount.
    2 points
  39. Version 1.0

    1,772 downloads

    Recycling your prefered beverage can for improving the printed fan duct life time with any material The central portion of the fan duct below the heat block can now better heat resists by using a beverage can thin and light metal sheet part (0.2mm thick) It's can be easy cutted with a scissor and it's easy formed by a forming printed tools PLA would be used now for printing the fan duct for those prefer this material
    2 points
  40. Version 1.0

    638 downloads

    Make a design table lamp electronically controlled. Change the shape of the lamp and light intensity according to your mood. Ready for 3D print - microcontroller Arduino - stepper motor - Joystick control. Full story on http://www.3lobitprint.cz/en/flola.html
    2 points
  41. Version 1.0

    5,558 downloads

    Playing around with some Colorfabb HT. Quite happy with this one. Obviously it has been post processed by sanding and polishing (the side facing down in the picture is the side against the glass so that was untouched though).
    2 points
  42. Version 1.0

    1,348 downloads

    Threaded Nut and Bold Pen / Pencil Holder for your Man Cave.
    2 points
  43. Version 1.0

    1,101 downloads

    This is the low friction stand for big filament spool (2 kg of plastic). Inner spool diameter - 50 mm, outer diameter - 300 mm.
    2 points
  44. Version 1.0

    1,421 downloads

    height: 32cm length: 55cm
    2 points
  45. Version 1.0

    1,257 downloads

    I reprinted my unicron model because I felt like painting it, but seeing as I haven't painted minatures in like 25 years i'm not that good anymore the acetoning was also too much and it cracked after spraying for some reason, but it serves its purpose. will do one with led eyes and a battery next after some remodelling. ive been away too long and feel like i need to start over.....:(
    2 points
  46. Version 1.0

    1,203 downloads

    Sorry for the lame photo, but I demolished this one experimenting on it a few hours later, lol. Obviously from the Gladiator movie, not perfect but you get the drift. Might do a moving version, if i have time, but this one is all one print, no gluing or construction.
    2 points
  47. Version 1.0

    1,256 downloads

    Remake of a great album and cover art. I'll metalize it soon and post the pics later, busy on something else at the mo...
    2 points
  48. Version 1.0

    5,675 downloads

    Just a mini circular saw I printed to accompany my mini drill. I also Printed little brief cases for them to go in as you can see in the video
    2 points
  49. Version 1.0

    2,185 downloads

    Here's a project that I've been working on for some years now with my good friend Darren. Our goal is to make the most accurate plans of the Eagle Transporter from the series Space 1999 from Gerry Anderson ( also creator of Thunderbirds ) This will be the studio scale version, and when ready it will be 44" or 111.76 cm
    2 points
This leaderboard is set to Amsterdam/GMT+02:00
×
×
  • Create New...