Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation since 04/20/2015 in 3D Print

  1. 10 points

    Version 1.0

    9,687 downloads

    The original dodecahedral kinetic sculpture by Stijn van der Linden a.k.a. Virtox. Made of five nested dodecahedra, each one is limited to rotate around its own axis. It was printed with dual extrusion on an Ultimaker 3 with water-soluble PVA support material.
  2. 8 points

    Version 1.0.0

    44 downloads

    1/40 Mosasaurus Nozzle : 0.4 Layer : 0.06
  3. 7 points

    Version 1.0

    2,890 downloads

    During my spell working in the Art department on 'Avengers Age of Ultron' I was asked by the production designer to build a prop to help dress the interior set of 'Stark Towers' The model was to show the new section of tower that replaced the damaged section from the original film. As I only had 4 weeks to build it (including 3d modelling) we needed to simplify the design a bit, hence the lower portion being in laser cut acrylic. Using my trusty Ultimakers I think I pulled off the desired effect, even if it only appeared in the movie for less than a second!
  4. 6 points

    Version 1.0

    465 downloads

    Star Wars Porg!
  5. 5 points

    Version 1.0.0

    102 downloads

    My special designed filament holder are directly for the original ULTIMAKER 3 (UM3) spools. Until now I use it for the 350g and 750g spools of 2.85mm filament (see pictures). Advantages: Easy to clamp or unloose in the spool Best way of storing the filament spools Spools are better stackable No unraveling of the filament End of filament doesn't have to be fixed in the small hole and the danger of breaking filament I'm looking forward to your feedback and especially if it works as well for the other material spools. Have fun. Posted at https://www.thingiverse.com/thing:2746539
  6. 5 points

    Version 1.0

    2,277 downloads

    Boon, The Tiny T-Rex from 3DKitbash
  7. 4 points
  8. 4 points

    Version 1.0

    330 downloads

    Why another phone dock? The new iPhone X is a few mm taller than the previous phones, so my old printed iPhone dock didn't work anymore. After some browsing I could not find any other dock I liked. The one I liked that doesn't fit does not exist for the X and I dislike mods on STLs/OBJs. The generic ones are typically clumsy or have other issues. So I decided to design one quickly from scratch. Here's the result I would like to share. I think there are not enough phone docks out there yet! :-)
  9. 4 points

    Version 1.0

    5,616 downloads

    To improve the CNC Router and not just to drill stuff, I also wanted to cut materials like cardboard, vinyl, paper, etc. Before to buy a lasercut, I did find in Internet a very interesting tool to transform the Spindle into a cutting machine. I wanted to buy the knife tool, but my spindle collet is 8mm, and most of the tools I saw doesn´t fit on it, so I decide to make my own, and after some failed prototypes and test, I made one that until now, after several test it works just great!. The blade can be coupled in two different positions, with a cut depth of 6mm or 10mm. Component list: - 2x bearings with 8mm inner diameter - 1x 8mm x 50mm rod - 2x collar - 9x M3 30mm screws with nuts and washers - 2x M3 16mm screws with nuts and washers - Blades I spend like 30€ on components, but that´s because I bought more than I needed, just to have spare parts, and the 3D printed parts, cost like 2€ with a 2,2kg Colorfabb XT Spoon.
  10. 3 points

    Version 1.0.0

    286 downloads

    elegant swinging smartphone stand The idea was a smartphone stand, where you have the ability to connect your standard charging cable... ... and then inspiration began to flow...
  11. 3 points

    Version 1.0

    452 downloads

    For everyone who want to have keychain with Ultimaker Follow me on Facebook : https://www.facebook.com/alen.kuhta/media_set?set=a.971249112929474.1073741827.100001331847671&type=3&pnref=story and Twitter : https://twitter.com/a_kuhta Thank you.
  12. 2 points

    Version 1.0.0

    25 downloads

    After searching the net again and again, I did not found a nice Dom Tower variant to print. So I decided to create my own versions: Single piece version (20 cm tall) Duplo compatible (big colored one, 53 cm tall) Lego compatible (PLA brons fill & Glow in the dark) Christmas edition (PLA silver, optional having 3 electric candles inside) Unfortunately the electric candles are still somewhere in China so I'm still curious how this will look like.. Stl file could be found here: https://cults3d.com/en/3d-model/architecture/dom-tower-utrecht (Single piece version only)
  13. 2 points

    Version 1.0

    656 downloads

    they show your guests where the toilet is...
  14. 2 points

    Version 1.0

    5,632 downloads

    Ever wanted to know what makes the Ultimaker robot tick? I was inspired by illustrations such as this one: http://altjapan.typepad.com/.a/6a00d8341bfd2253ef014e8936f006970d-pi The "maker globe" was created using a NASA satellite image maps of lights on the earth at night in order to generate the gears. I assumed that the brighter areas on the map would have a greater density of Makers, so there are more gears populating those areas on the globe. The lines in the oceans were derived from images of shipping lanes. I wanted to distill the idea of Makers working together and ideas traveling freely across the globe. I will be sharing these models for everyone to enjoy on youmagine shortly.
  15. 2 points

    Version 1.0

    2,165 downloads

    Endo the 3D printed Action Figure
  16. 2 points

    Version 1.0.0

    10 downloads

    Hi there, I designed a little dual colour print for christmas Print files Merry Christmas
  17. 2 points

    Version 1.0

    374 downloads

    Printed in Extrudr Greentec on a modded UMO+. The model was scaled down to 70% to fit on our doors. Slightly sanded and painted with matte clear coating.
  18. 2 points

    Version 1.0

    763 downloads

    Printed in 3 parts. Hight: 340mm Diam: 120mm
  19. 2 points

    Version 1.0

    1,403 downloads

    Impression 3D maquette, surface totale du projet 283 m² 1.5 cm / 1 m dimension maquette 42cm / 43cm / hauteur 9 cm
  20. 2 points

    Version 1.0

    5,168 downloads

    I wanted a more integrated solution for mounting a Raspberry Pi Camera on the UM2, so i designed one. I am using a third-party camera module with a 36x36mm board and a M12 lens mount.
  21. 2 points

    Version 1.0

    633 downloads

    Make a design table lamp electronically controlled. Change the shape of the lamp and light intensity according to your mood. Ready for 3D print - microcontroller Arduino - stepper motor - Joystick control. Full story on http://www.3lobitprint.cz/en/flola.html
  22. 2 points

    Version 1.0

    1,101 downloads

    This is the low friction stand for big filament spool (2 kg of plastic). Inner spool diameter - 50 mm, outer diameter - 300 mm.
  23. 2 points

    Version 1.0

    1,412 downloads

    height: 32cm length: 55cm
  24. 2 points

    Version 1.0

    2,185 downloads

    Here's a project that I've been working on for some years now with my good friend Darren. Our goal is to make the most accurate plans of the Eagle Transporter from the series Space 1999 from Gerry Anderson ( also creator of Thunderbirds ) This will be the studio scale version, and when ready it will be 44" or 111.76 cm
  25. 1 point

    Version 1.0.0

    103 downloads

    48 Hour Print 0.1 MM LH
  26. 1 point

    Version 1.0

    555 downloads

    - absorbs the vector-forces => longer life for and lower noise from the printer - level the printer
  27. 1 point

    Version 1.0.0

    35 downloads

    Creation of a small box for a bed remote.Printed in Centaur PP from Formfutura. Specs : Printer : UM2 + bondtech feeder + Olsson Bloc Material : Centaur PP (polypropylène) de Formfutura Nozzle : 0.6mm Layer Height : 300microns Speed : 40mm/s Wall : 2mm Supports : Everywhere at 50° and 20% Fan Speed : 100% Printing Time : 3h10 I used brown PP scotch for the bed adhesion.
  28. 1 point

    Version 1.0

    812 downloads

    Quality Layer height: 0.1mm* Initial layer thickness: 0.3mm Bottom/top pattern: lines Skin perimeter line count: 0 Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers). *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double. Speed setups: Infill speed: 50mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt speed: 30mm/s Amount of slower layers: 4 Infill: Infill pattern: Grid Line distance: 3mm Infill overlap: 20% Infill layers: 0 Support: Enable support: Check Placement: Everywhere Overhang angle: 30° X/Y distance: 0.7mm Top distance: 0.2mm Bottom distance: 0.2mm Stair step height: 0.5mm Join distance: 0.7mm Area smoothing: 0.6mm Use towers: check Pattern: Grid Line distance: 1.5mm Platform adhesion: Type: Brim Brim line count: 10 (up to 20, depending on the model’s height) Other 3D printing recommendations: Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
  29. 1 point

    Version 1.0.0

    148 downloads

    This is iPad Air stand. You can change the incline of the tablet by pushing the button up and pulling your iPad up or down.Printed with PLA. There are 5 main parts of the stand: Main body consists of two parts, which have juts and holes to ease assembling. Cilinder with groove to insert iPad. Button with lever (consists of two parts to ease printing) Tooth Spring (i took it from ordinary ballpoint pen) Parts of main body and of the button are glue together with dichloroethane (as i used PLA). Before gluing you should insert button with lever, tooth, spring and cylinder into one part of the main body. Then smear it with dichloroethane and connect with the second part of the main body.
  30. 1 point

    Version 1.0.0

    25 downloads

    I designed and printed a dolphin jumping out of the sea. The dolphin was printed with Bronzefill. The base was printed using NGEN clear for the outer walls and blue PLA for the infill, thus creating a nice blueish sea. Printfiles: https://www.youmagine.com/designs/dolphin Marco
  31. 1 point

    Version 1.0

    133 downloads

    Needed a custom mount for the IKEA Östanå lamp. Couldn't find one so I created one in Fusion 360. The two gaskets from the original mount can be used with this mount.
  32. 1 point

    Version 1.0

    119 downloads

    Thank you @vlada.mladenovic for sculpting, modelling 3D ear and @sculptures_unique for idea. @umetnickaskolanis thanks. Working progress. Used PLA @ORBITECH And the best 3D printer @ultimaker
  33. 1 point

    Version 1.0

    139 downloads

    11 x 54 x 15.5 inches. Printed in sections in PLA, epoxied together, and painted in acrylics. This was a photogrammetry project made from photographs taken on site in Antarctica as a 2015 grantee of the National Science Foundation Antarctic Artists and Writers Program. It's on view through Jan. 12, 2018, in the exhibition "Walking in Antarctica" at Goucher College. More here: http://www.goucher.edu/rosenberg-gallery/exhibits/walking-in-antartica
  34. 1 point

    Version 1.0

    1,704 downloads

    Quality Layer height: 0.1mm* Initial layer thickness: 0.3mm Bottom/top pattern: lines Skin perimeter line count: 0 Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers). *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double. Speed setups: Infill speed: 50mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt speed: 30mm/s Amount of slower layers: 4 Infill: Infill pattern: Grid Line distance: 3mm Infill overlap: 20% Infill layers: 0 Support: Enable support: Check Placement: Everywhere Overhang angle: 30° X/Y distance: 0.7mm Top distance: 0.2mm Bottom distance: 0.2mm Stair step height: 0.5mm Join distance: 0.7mm Area smoothing: 0.6mm Use towers: check Pattern: Grid Line distance: 1.5mm Platform adhesion: Type: Brim Brim line count: 10 (up to 20, depending on the model’s height) Other 3D printing recommendations: Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
  35. 1 point

    Version 1.0

    893 downloads

    Quality Layer height: 0.1mm* Initial layer thickness: 0.3mm Bottom/top pattern: lines Skin perimeter line count: 0 Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers). *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double. Speed setups: Infill speed: 50mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt speed: 30mm/s Amount of slower layers: 4 Infill: Infill pattern: Grid Line distance: 3mm Infill overlap: 20% Infill layers: 0 Support: Enable support: Check Placement: Everywhere Overhang angle: 30° X/Y distance: 0.7mm Top distance: 0.2mm Bottom distance: 0.2mm Stair step height: 0.5mm Join distance: 0.7mm Area smoothing: 0.6mm Use towers: check Pattern: Grid Line distance: 1.5mm Platform adhesion: Type: Brim Brim line count: 10 (up to 20, depending on the model’s height) Other 3D printing recommendations: Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
  36. 1 point

    Version 1.0

    1,525 downloads

    I got tired of the old 3D printed lampshades for our self-built LED lighting. So I designed new ones with Ebony woodfill and blue. Dual extrusion print, two parts: bottom (spiralize mode) and top (wood and blue) with a slit to get the cable through. The woodfill seems to have some air in it, tiny holes and crackling sound during printing. UPDATE: I played around with extrusion rate and decided to consider the tiny holes as a feature now
  37. 1 point

    Version 1.0

    459 downloads

    First test print since fixing my um2 numerous times... hopefully not for a while again. Usual post work.
  38. 1 point

    Version 1.0

    498 downloads

    A test sculpt of my friends dog.... still trying to get my UM2 back to spec. Didnt realise the 35W heater needed a PID alteration or something, but hopefully I'll have that sorted and will be back to making near flawless prints. No closeups here because they are not worthy of closeups.
  39. 1 point

    Version 1.0

    631 downloads

    This is my new Filament Dryer. It´s for 4 Spools of Filament.
  40. 1 point

    Version 1.0

    1,069 downloads

    Hi ultimakers, Here is one of my projects which is made on Ultimaker3.
  41. 1 point

    Version 1.0

    414 downloads

    Hair Dryer Diffuser
  42. 1 point

    Version 1.0

    8,107 downloads

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings: Quality Layer height: 0.1mm* Initial layer thickness: 0.3mm Bottom/top pattern: lines Skin perimeter line count: 0 Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers). *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double. Speed setups: Infill speed: 50mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt speed: 30mm/s Amount of slower layers: 4 Infill: Infill pattern: Grid Line distance: 3mm Infill overlap: 20% Infill layers: 0 Support: Enable support: Check Placement: Everywhere Overhang angle: 30° X/Y distance: 0.7mm Top distance: 0.2mm Bottom distance: 0.2mm Stair step height: 0.5mm Join distance: 0.7mm Area smoothing: 0.6mm Use towers: check Pattern: Grid Line distance: 1.5mm Platform adhesion: Type: Brim Brim line count: 10 (up to 20, depending on the model’s height) Other 3D printing recommendations: Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default. Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.
  43. 1 point

    Version 1.0

    1,659 downloads

    So i didnt like the cardbox version of my nozzle box so i made a new one ,and i like to share it with you .
  44. 1 point

    Version 1.0

    782 downloads

    First piece that I have done using Copperfill and still not sure how to best finish it. Used a Dremel with a brass brush at low speed then a polishing disk also at low speed. The process seems to work though it actually seems to highlight the layers!
  45. 1 point

    Version 1.0

    1,295 downloads

    Credit where credit is due: I found this fantastic design on Martin Hansen's website (http://www.mysupercharger.net) and decided my phone needs a supercharger exactly like this beauty Completely printed in Innofil3D PLA (white, grey and red). Photo shows test-fit as it came of the bed with a minor bit of sanding on the base and grey rods to allow assembly. (apologies for the crappy photo)
  46. 1 point

    Version 1.0

    2,437 downloads

    We just bought a new Fiesta and I thought it would be fun to print a model. So here it is :-) Sliced with Simplify3D. I like the result, the model actually shines like gold :-)
  47. 1 point

    Version 1.0

    1,593 downloads

    I downloaded these files from Thingiverse and modded the cover by adding dimples around the exterior surface to echo the gear shape of the base. Filaments used: bioFila Silk, Colorfabb Shining Silver and Proto-pasta Aromatic Coffee.
  48. 1 point

    Version 1.0

    1,489 downloads

    PETG / Carbon & Kevlar ® Nanovia
  49. 1 point

    Version 1.0

    1,286 downloads

    Entry for contest. Gorilla printed with Colorfabb bamboo fill Bananas printed with Colorfabb XT Yellow Kittypool printed with Colorfabb XT Blue Photograph shot with Canon 60D swimming pool in the background. Gorilla designed by Bauermaker (https://www.youmagine.com/designs/lowpolymonsta) Bananas and Kiddiepool designed by me
  50. 1 point

    Version 1.0

    2,997 downloads

    This custom camera loupe is designed by @Valcrow from Redicubricks. It was a perfect fit for our camera team during an upcoming Ultimaker video!
This leaderboard is set to Amsterdam/GMT+02:00
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!