Jump to content
Ultimaker Community of 3D Printing Experts

Leaderboard

Popular Content

Showing content with the highest reputation on 02/28/2018 in all areas

  1. This the third object I've printed, the spiral vase! Very happy with it, all default settings, no support, UltiM white PLA, 200microns and no infill. 99% scale at 198mm, 6h 50min print time
    2 points
  2. Thanks for all the replies and solution suggestions. It appears to have to do with Cura for Mac. I downgraded to Cura 3.1 and all is fine. 3.2.1on my pc worked fine also... Thanks again. Hope they fix this issue with the next firmware update...
    1 point
  3. thank you for that. I know, the bricking issue is at the for front of my mind but there is something bugging me about the upgrade I did and want to check it before I start getting emotional about it. will let you know how it goes. Rebekah Anderson
    1 point
  4. Ok, mais la, tu imprimes du PLA et le PLA est un filament qui doit être refroidi et avec une enceinte fermée, il doit faire trop chaud et du coup, le PLA continue à travailler. Le 0.06 n'a d'intérêt que sur les surfaces courbes ou sur les impressions vraiment très détaillées ou imprimées avec une buse de 0.25 par exemple....
    1 point
  5. Maybe your printer cable was loose? It has to kind of snap in. It should not come out without sliding the outer part first.
    1 point
  6. That shows you how tired I was when I wrote that. I actually ran that through the Cura Connect without saving to g-code. :( But, I did dump the logs and am resetting my printers right now. I think something glitched a bit with Cura Connect as I had to reset both printers for them to be seen and available on the browser. The monster that took just over 9 days was run through the USB stick on the other machine. And, for the slight aggravation, I am most happy to have returned from the trip to a working printer and no atomic filament mushroom clouds up me printheads....
    1 point
  7. Implemented it! You can follow the progress here: https://github.com/Ultimaker/Cura/pull/3411 You could beta test the next release; the Cura team doesn't really distribute pre-beta builds...
    1 point
  8. I strongly recommend you stick with cura 15. At least for the first 100 prints. Cura 15 works great and I still use it on some of my printers. Cura 3.X has a huge learning curve and will waste time trying to get things working - it will be a distraction.
    1 point
  9. I'd like to share the obvious advantages that Adaptive Layer has afforded me in my daily work flow. We are a manufacturer of plastic bottles. Not very sexy, but somebody has to do it . . . On this particular design, Adaptive Layer saved over 30 minutes on a 5 hour 15 minute build compared to without it. At the same time improving the overall look and quality of the finished model. The angular sections (dark blue at 0.10 layer) of the bottle have much finer stair steps per layer and the thread finish of the neck of the bottle has superior detail as well. Th
    1 point
  10. I don't know what causes these issues, but it's VERY specific to where the object is, how it is rotated, etc. Any move will change it (perhaps float it a mm over the bed).... And yeah, anything you can tweak in the printer settings which might make the issue go away, the more likely the dev team can fix it.
    1 point
  11. Je vais tenter de répondre mais en faisant abstraction de ton imprimante car je ne la connais pas cette Anet 06, pourtant, j'ai connu une Annette mais elle doit être en prison maintenant (une longue histoire....) sachant que je ne suis pas un spécialiste du Gcode.... 1/ Pour qu'il y ait un décalage d'une ou plusieurs couches sur un fichier STL, il faudrait que le bug décale les couches en X/Y sans toucher à Z : je n'y crois pas mais sait-on jamais.... Quand du dis que tu as "réparé" le STL, tu as utilisé quoi ? Si tu regardes dans CURA (quelle version utilises-tu d'ailleurs ?)
    1 point
  12. Hi Steve, Yes, that is exactly what I needed and you are correct, I have found someone to do it. I appreciate your reply and will keep your contact info at hand. Cheers, Phillip Jones
    1 point
  13. some users have resolved it by using cura 3.1 but some also say the latest firmware causes this, so i would suggest to try with 3.1 and if it doesnt work change the firmware
    1 point
  14. nevermind figured it out, only need to swap two wires round motor side pins 3 and 4
    1 point
  15. waiting to see the video!
    1 point
  16. This is one thing that makes this feature so fuzzy and hard to understand. The UI reflects the developers mindset...not the end-users mindset. (yes, UI is tricky...I know...I work with such stuff daily)
    1 point
This leaderboard is set to Amsterdam/GMT+02:00
×
×
  • Create New...