Jump to content

tecnao

Member
  • Posts

    9
  • Joined

  • Last visited

Personal Information

  • 3D printer
    Ultimaker Original
  • Country
    FR
  • Industry
    Engineering

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

tecnao's Achievements

0

Reputation

  1. Hello, I wanted to improve my precious UM printer running with its 1.5.4 board. As the Ultipanel was too expensive for me, I bought a cheap LCD12864 LCD module with SD card from greeetech. It comes with its two 10 pins cables to link to the UM ext pin board. Unfortunately, nothing works as expected . I already spent 2 days through different forums to find a solution, no way. I tried all these methods : Update marlin V1 with u8glib (and modify config.h as advised here :http://www.geeetech.com/forum/viewtopic.php?f=23&t=17040) and send to UM -> Nothing lights on no beeps. Reverse the cable as advised here : https://ultimaker.com/en/community/4614-question-about-lcd-controller-substitute. + update marlin RC with u8glib -> Backlight ok and beep. But nothing on the LCD. Add a direct 12V line to avoid the USB line as explained here :http://wiki.ultimaker.com/File:Patching_old_electronics_to_selfpowered.png I tried so many combinations that I don't remember all of them, but never succeed to have an autonomous UM as required. I even had one which which has burnt the remaining PLA in the head up to smoke and bubbles, using bultimaker (probably with wrong parameters) : https://bultimaker.bulles.eu/ Anyway, your help would be highly appreciated, as the usb port is full of contact failures so the autonomous option will allow to use this vintage printer for a few more years. Thanks in advance.
  2. Bonjour, le changement de fil en cours de fabrication se fait très bien de mon coté en tirant sur le fil, une fois l'extruder désactivé et surtout avec le tête chaude. La manip est plus facile depuis que j'ai mis la nouvelle version du nez chauffant. Il reste toujours un gonflement en bout de fil qu'il faut couper avant la remise en place ultérieure, mais le retrait se fait tout de même tant que le fil est chaud en bout. Bonne continuation. Sébastien
  3. tecnao

    Installer Cura

    Bonjour, ça risque de ne pas faire avancer énormément la chose pour toi, mais j'ai réussi à faire fonctionner mon Ultimaker grâce à Cura sur un PC équipé windows 7 en 64bits. Win32, c'est la version 32 bits du logiciel. Il faut savoir quelle version est installée sur ton PC. D'après ce que je me rappelle avoir lu (mais je peux me tromper), Cura fonctionnerait également sur windows XP. Bonne continuation. Sébastien
  4. Top, ça fonctionne. Et je viens de tomber sur la page d'explication du problème sur le wiki; je n'avais pas tapé "first layer" pour tomber dessus... Merci du coup de main. A+
  5. Merci beaucoup pour cette réponse rapide. J'avais tendance à plutôt augmenter la distance entre le plan et la buse au lieu de la diminuer. Je vais jouer sur les vis de réglage d'horizontalité. Je teste cet aprèm. A+
  6. Bonjour à tous, heureux de voir que je vais peut-être pouvoir trouver une solution à mon problème sans fouiller trop loin dans tous le termes anglais qui pourraient être utilisés sur le forum pour dérire mon problème. J'explique : j'ai enfin réussi à piloter comme je voulais mon ultimaker, mais je suis confronté à un problème majeur : le PLA ne tient pas en place sur la platine et se fait entraîner par la buse dans son balayage. Impossible de créer quoi que ce soit, aucune adhérence sur le scotch bleu. A votre connaissance, s'agit-il d'un problème de réglage du soft (vitesse de sortie du PLA, mais le moteur d'extrusion me sort bien 100mm quand on lui demande 100mm) ou un réglage matéreil (j'ai essayé de jouer sur la hauteur du Z à 0, mais rien n'y fait) : le PLA en sortant de la buse s'obstine à se coller et s'entortiller autour de la buse sans jamais se déposer sur le lit ou uniquement après plusieurs passages, mais il est inévitablement entraîné par la buse quand elle repasse à proximité. Toute suggestion et surtout tout retour d'expérience sera le bienvenu. Je vais poster aussi sur le forum anglais au cas où, car je n'ai pas trouvé de sujet sur ce point. Merci d'avance.
  7. Bingo, thanks. Works now, just have to adjust parmaeters to avoid the noze bringing all the plastics during the movement ... Let's search on the forum ... Really nice software, wonderful job. Thanks again.
  8. Hello, first print today after several weeks of inactivity, I tried to use the Cura software. I'm working on windows 7 64 bits. I followed the "noobies" answer I found on the forum (i.e. installed arduino, uploaded marlin) but after the first run wizard tests (all passed), I have this message when I try to print a stl file: Exception in thread Thread-7: Traceback (most recent call last): File "C:\Program Files (x86)\Cura_RC3\python\lib\threading.py", line 552, in _ _bootstrap_inner self.run() File "C:\Program Files (x86)\Cura_RC3\Cura\gui\sliceProgessPanel.py", line 127 , in run p = subprocess.Popen(self.cmdList[self.fileIdx], stdout=subprocess.PIPE, std err=subprocess.STDOUT) File "C:\Program Files (x86)\Cura_RC3\python\lib\subprocess.py", line 679, in __init__ errread, errwrite) File "C:\Program Files (x86)\Cura_RC3\python\lib\subprocess.py", line 893, in _execute_child startupinfo) UnicodeEncodeError: 'ascii' codec can't encode character u'\xe9' in position 159 1: ordinal not in range(128) :oops: Any idea to solve this ? Thanks
  9. Hi Didero, did you experinced this problem only qith the bushes in the blocks, as I also have this problem both on the blocks and on the heating noze : every hole seems to be a bit too large for the bushes and bearings, creating excessive backlash that I assume will affect the final result. What kind of glue did you use for this ? Thanks. PS : seems that the french machines have to face the same problem...
×
×
  • Create New...