fritz99

Hello ! I am printing with ABS and a hotbed. Extrusion temp is 250 degrees centigrade. Hotbed temperature is 145 degrees centigrade. Cooling fan has 60 %. Printing is fine but the corners bend up from the hotbed appr. 0.7 mm. Is there a secret that the corners keep on the hotbed and do not bend up ? Fritz

Hello ! At the start of printing the software heats the hotend to 260 degrees. That is ok. After start of printing the temperature lowers to 230 degrees. And then it rises to 260 degrees again and stays there. What is wrong ? Fritz

Hi Fritz Add to you Gcode the following M190 S110 ; Turn HBP on and set to 110 degrees M140 S0 ; Turn HBP off Took me forever to find that when I built mine and it doesn't work in RepG 34 only RepG 26 and Printrun etc. Good luck Did you put this into the Gcode header in netfabb ? Fritz

Hi Fritz Add to you Gcode the following M190 S110 ; Turn HBP on and set to 110 degrees M140 S0 ; Turn HBP off Took me forever to find that when I built mine and it doesn't work in RepG 34 only RepG 26 and Printrun etc. Good luck Thank you very much. I will try it Fritz

Does nobody know how to activate the hotbed in netfabb for ultimaker ? I really need it for ABS printing. Thank you. Fritz

Hello ! Is there any gcode documentation of all marlin commands ? Fritz

How can I do this in software 12.11. It has no more printrun. Fritz

Hello ! I have the following problem : In quickprint with ABS the hotend starts with a temperature of 260 degrees. The printing starts. Then the temperature during printing drops to around 230 degrees. Then very very slowly the temperature comes back to 260 degrees. Hardware is ok !!!! I print with a hot bed. This is a big problem for printing with ABS because the ABS gets not hot enough during that time and the printing is unuseable. What is the problem ? Fritz

Ok. But I often have several gcode files for the same model that I've renamed with their parameters. Is it possible to get just a simple load button, or that if you select a gcode from the main window that on load finish it pops you into the print window? I totally agree, Daid's suggestion works in an engineering world, but is utterly not intuitive for the rest of humanity, especially if it is not explained anywhere. a simple 'load gcode" button will fix this, now that Daid killed off print run from the package (which may not have been the wisest choice at this point of the development stage ). This would be very helpful especially for Gcode of very complex models that cannot be sliced with CURA and are sliced by an other software like netfabb. Fritz

Hello ! For me it is also working ok. Fritz

Which slicer shoud I use ? Can I print the sliced file with CURA ? Because I have a hotbed for ABS printing, I have to use CURA for printing. CURA is the only software that can control a hotbed, or am I wrong ? Fritz

I have a hotbed. Fritz

And what can I do to fix this ?

Hello ! When I want to prepair for printing a complex model, then CURA says that there is something wrong and stops. The same model stl file is ok in netfabb. Please help. Fritz

Till today I had only the release candidate and not the final software. Fritz

The problem is that the raft is also under the printed piece and cannot be cut off. So the underside is not as it should be. Fritz

ABS Fritz

Hello ! When I want to print with the quickprint mode with ABS it does not matter if I check or uncheck the "print support struchture ". It always prints the support structure. Please help Fritz

Hello ! The download for windows does not work. There is always a server error. Mac und linux work. Fritz

Hello ! In the advanced configurations I cannot find an input field where I can define the hotbed temperature for printing. Please help. Fritz

Hello ! Can anybody explain in detail how to connect the bed and the Thermistor to the ultimaker controller and control it with the netfabb software ? Fritz

Hello ! Is ist possible to activate a hotbed in netfabb ? Which out and inputs of the hardware can I use ? Fritz

Thank you Ian ! Can you tell me which are the best ? Please the link. Fritz

Hello ! I am printing with netfabb. Everything now is ok. Only the printed circles are nor round. They are like an elypse. Is it possible to correct it with some parameter ? Fritz

Hello ! I print with 205 degrees. I have Hotend V2 but the hose is still coming out !!!!!! Fritz