Jump to content

nutz95

Dormant
  • Posts

    1
  • Joined

  • Last visited

    Never

nutz95's Achievements

0

Reputation

  1. I've been using successfully Cura for my Prusa i3 8'' with magma hot end (i can use ABS only with the hot end right now) Here are my settings: Dump it into any .ini file and load it with cura (V13.06.4) [profile] layer_height = 0.2 wall_thickness = 1 retraction_enable = True solid_layer_thickness = 0.9 fill_density = 20 nozzle_size = 0.4 print_speed = 70 print_temperature = 225 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_bed_temperature = 90 support = None platform_adhesion = Brim support_dual_extrusion = False filament_diameter = 2.85 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_flow = 100 retraction_speed = 30 retraction_amount = 4.5 retraction_dual_amount = 16.5 bottom_thickness = 0.3 object_sink = 0.0 overlap_dual = 0.2 travel_speed = 150 bottom_layer_speed = 20 infill_speed = 100 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 fan_layer = 1 fan_speed = 100 fan_speed_max = 100 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 15 support_rate = 75 brim_line_count = 15 raft_margin = 5 raft_line_spacing = 1.0 raft_base_thickness = 0.3 raft_base_linewidth = 0.7 raft_interface_thickness = 0.2 raft_interface_linewidth = 0.2 fix_horrible_union_all_type_a = False fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = (lp1 . object_center_x = -1 object_center_y = -1 [alterations] start.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end.gcode = ;End GCode M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = nextobject.gcode = ;Move to next object on the platform. clear_z is the minimal z height we need to make sure we do not hit any objects. G92 E0 G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 F{travel_speed} ;move Z up a bit and retract filament even more G90 ;absolute positioning G1 Z{clear_z} F{max_z_speed} G92 E0 G1 X{object_center_x} Y{object_center_y} F{travel_speed} G1 F200 E6 G92 E0 switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. G92 E0 G1 E-36 F5000 G92 E0 T{extruder} G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} G1 E36 F5000 G92 E0
×
×
  • Create New...