Jump to content
Ultimaker Community of 3D Printing Experts


  • Content Count

  • Joined

  • Last visited

Everything posted by ultimore

  1. You changed something else than just "104gt for ext0 and 100k epcos for bed", the firmware you posted does not match these settings. Well if it worked 30 seconds, it means that the build generated valid Arduino code, so the builder itself is not broken. It remains 2 possibilities: Marlin is broken for your selection. I am skeptical, but there is always a possibility. However I can't investigate that until I know exactly which options have been used in the builder There is something wrong with your hardware setup (obviously neither the hotend nor the bed are standard Ultimaker comp
  2. Only sensor to 104GT, and baud rate to 115200. Nothing else. First unresponsive board was to 104GT and sensor for heated bed + 225000 baud rate (I thought that baud rate caused that I cannot upload firmware either through Cura or Arduino IDE). I mean Arduino Mega 2560 (pretty much regular arduino board). After disconnecting original Arduino Mega board I wasn't able to upload anything (timeout) Cura / Arduino IDE. Same happened with second board (original Arduino Mega 2560). I have uploaded other firmware (Cura/Arduino IDE) before this one and had no issues. After I've uploaded a firmwar
  3. This is build that i installed. It worked for about 30 seconds. Then arduino became warm and now i cant upload nothing to it. this is build that i installed. http://dropmefiles.com/vUGUW
  4. I've got the same problem.... I made a firmware with 104gt for ext0 and 100k epcos for bed and now i cant connect to 3d printer with any tool and can't update the firmware...
  5. Hello everyone! I have a problem with my ultimaker original. There is an error. [ERROR] Error:0: Extruder switched off. MAXTEMP triggered !Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) If i connect UO electronics without any wire connected, should it give me this error? Sorry for my bad English. Thank you!
  6. Maybe someone has an UMO? Really need this, because my pcb lies near printer...
  7. Yes! and another one is a little bit longer. Can you help me to find it?
  8. i'm not sure this will fit ultimaker original... They are like a nuts.
  9. Sorry, can't open this page(( http://prntscr.com/8sq8zr I need them to hold on electronics on ultimaker original
  10. Hello everyone, i have a problem. I lost my threaded spacers. Can someone tell me the exact size of them? these white things i'm talking about.
  11. Hi there, is there any way to help you to translate cura to Russian for example? I will do it myself for free, only mention my name. If you need such a help, let me know. TY
  12. I think that problem is with your feeder stepper driver, try to increase voltage a bit, and loose your feeder screw. As for me, my ABS settings are - 250 temp, 100 HB, 0.1-0.15 layer height ( more than 0.15 my ultimaker feeder stop working on 4th layer.
  13. Hi there guys , I had a trouble, my z axis started to miss some steps when going up. Tried to increase voltage on stepper driver, lubricated the 2 z rods. But it still miss, thx for your help!
  14. So the problem was that filament just couldnt het through the tube to the hotend, because of bad tube positioning and i forgot to use blue clamp. Now its okay, but ive broke my thermistor . Can i connect k type thermocouple without dissoldering 4.7k resistor?
  15. Need your help. After a few hours of using hotend, I think filament stucked in extruder, I couldnt push filament to the extruder. What can I do? And how to take off tube from the. E3d extruder?
  16. Hi all, i need your help. Think smth wrong with print quality, dont know the problem.is this happrn becausr of cura.or snth else. Thabk you for your reply http://i61.tinypic.com/2nlvm1l.jpg
  17. I got it, thank you) Maybe u know where in old electronics such as old tv or radio i can find a 4.7k resistor? ))
  18. Ok but can you tell me the difference between e3d thermistor and for example K type thermocouple which i use before e3d with heated bed
  19. Should i connect it to thermocouple sensor board or direct?
  20. And guys, i tried to connect e3d thermistor like original one, changed in firmware to ATC Semitec 104GT-2 but temperature is incorrect, it showss me about 100 C. What should i do?
  21. Can you please post here, how to mount your hot end plastic? i tried to mount and it doesnt touch end stopper, post photo here pls!
  • Create New...