Jump to content
Ultimaker Community of 3D Printing Experts

danilius

Member
  • Content Count

    362
  • Joined

  • Last visited

  • Days Won

    7

Everything posted by danilius

  1. Really nice piece of work. You can use to hold your vinyl LPs if nothing else.
  2. It's possible that the hobbed nut itself is loose. There is a grub screw on it which might require tightening.
  3. @Nicolinux, that's very impressive, but where do you get bananas that shape? Or is this for storing some other kind of fruit?
  4. My theory is gremlins, for what it's worth.
  5. Well, I got my new bearings from Ultimaker (worked out cheaper than buying them from Ebay, interesting) and swapped them out on the left hand side. I think the noise had gone for good, but remains to be seen. So, how painful was the experience? Actually, not so bad. The bearings slide off quite easily, and they were the least of the problems. I did not have to retention the motor belt either since I left the motor attached to the wall. What I did discover was interesting. Some of the screws had their heads stripped and were difficult to remove, so they had been over-tightened in the factory.
  6. I think one of the shaft bearings is going, because I'm getting weird problems when printing. If printing a square, on the front and left side the walls don't touch properly, and the infill in the rear left hand side is noticeably thinner than the front right hand side. Circles have walls that do not touch properly. Now, you might think the temps or e-steps are incorrect (I swapped out the standard hobbed nut for a grooved one) but I checked both of those elements exhaustively. So, how does one change the bearings? Has anyone got a video or some tips? Is it a complex operation? Where can I b
  7. I use Singer sewing machine oil, and periodically oil the shafts. Having listened to the bearings closely, I think it is one of the rear left-hand bearings that sounds like it has an issue, the ones mounted in the walls. Has anyone replaced those? Is it difficult to do?
  8. Awesome prints - they look so waxy. The Bronze one with verdigris is just a mind-blower.
  9. I moved the head by hand, and it seemed fine and did not make that noise either. It's possible the bearings are going there, or maybe one of the ball bearings on the drive shafts. Problem is that I can't seem to track it down, and don't fancy replacing the shaft bearings if I don't really need to. Oh well, it looks like I have some fun ahead of me :(
  10. For a while I've been getting this noise from the y-axis of the printer, but I have no idea where it's actually coming from or what the problem is. I have recorded some of this here, and you can see that the noise only appears on longer moves on the y-axis. Short moves and x-axis moves do not make the same noise. Anyone have a clue what the problem is?
  11. I have been using ABS juice exclusively for a while now, and figured now is a good time to share my experience with it, since there are so many posts regarding bed adhesion. I use juice for PLA, ABS and Nylon (Taulmann Bridge) on borosilicate glass and regular float glass (way cheaper, and works just as well). My recipe is quite simple, I stuff some white ABS filament into a bottle (a thin solution of white ABS makes for an almost entirely transparent film), fill it with acetone and then let it stand for a while. Every now and then I shake the bottle. I have tried thicker and thinner version
  12. I rarely use the fans, even when printing PLA, since they only seem to benefit when printing really small areas. For most prints I simply keep them off entirely. ...a host of other reasons. I print from a roll that sits on a custom holder I made with ball bearings. The only problem I encounter with that is a tangle, something more likely to occur when using loose filament.
  13. @cloakfiend, I went through a horrible hour or two trying to free the thermal doohicky from the old, standard UM2 block, and failed miserably. However, having learned a great deal from previous life experience, I only undertook the change having spare parts at hand, which I of course eventually needed. But it was worth it for several reasons. First of all, now I am no longer afraid of doing a head rebuild. It makes me around 20 minutes to strip everything down and put it back together again. Secondly, the Olsson block has made life much easier. Blocked nozzle? Take it out, put in an unblock
  14. I don't think this will work, because the it makes no difference how much of the "tip" of the thread you remove, you still need clearance above and below the mating thread profile. I "hand-make" my threads because of this, by making a spiral extrusion. In Blender this is a doddle, there a screw modifier that does all the hard work in a matter of a few clicks. In FreeCAD this is a bit more painful, but still eminently doable using a helical extrusion path.
  15. I usually leave a 0.1mm or slightly less, depending on how tightly the nut and bolt have to fit. It also depends on how accurately your machine extrudes the width of each line, which of course will affect the tolerances as well. So, experiment away, until you change rolls and discover that every colour even from the same manufacturer behaves differently, and there go your measurements :-)
  16. I tend to avoid supports as well, but if I have no choice I plan the model very carefully to minimize the amount of support needed. To remove supports, I use jewellery pliers, a craft knife and my fingers! Lately I have been using slic3r exclusively, and it offers really great control over supports, and some impressive results if tweaked carefully. It has many options for support than Cura does. Bit of a pain to setup, mind you, and it is far less stable than Cura, and takes aaaaaaggggeees on high poly models compared to Cura.
  17. Love your latest work, especially all this gorgeous copper plating. I doubt the copper plating will add even a gram of structural support to your shroud since the metal is so thin, so much thinner than silver foil.
  18. This topic has been covered extensively all over the forum, but essentially I use UHU stic (that's how they misspell it), heat the bed to 60C and draw lines across the glass. The heat helps to melt the glue a little. After that, it works for about a week, even after being overprinted and being cooled in the freezer (makes for easy removal). The stick that came with the Ultimaker 2 simply does not compare. If I'm not too lazy, I use acetone juice even for PLA, and spread it by dribbling a line of juice across one edge of the bed and then using an 8mm steel rod like a rolling pin to create an e
  19. I suggest uploading a sample gcode file in which you observed this error, since by updating the firmware you have eliminated any custom settings that might have caused this. At this point, given the information you have supplied, the next logical step would seem to eliminate any gcode errors.
  20. While I have found 1.99 stable, the layer view stutters quite badly, in that when dragging the layer slider up and down, it's really not smooth, whereas 15.04 (which I still use for production) is much smoother on layer view.
  21. A great tool I use for clearing clogged nozzles are the twist-ties that come with plastic bags. I don't even strip off the plastic, just shove it into the nozzle with a pair of small pliers. Works a charm.
  22. Are there regular/nightly builds available of Cura? I really don't fancy building it myself.
  23. When I first got my Ultimaker, I used the glue stick that came with it for PLA. Results were so-so on big pieces. After a while I tried UHU stic and that was superb, with the disadvantage that parts were difficult to remove. That was solved by either allowing the bed to cool to room temp or sticking it in the freezer. For ABS I use ABS juice only. I have printed some seriously large parts with this (30 hours + prints) and had no warping issues. I used to close up the Ultimaker with paper everywhere, concertina-folded paper on top. I simply don't bother anymore, because my room does not have b
  24. The way I see it, there are two issues here: 1) Are you going to get a decent printer? 2) Just how ethical is it, since these guys are using all the research Ultimaker did to build their clone without passing anything back to Ultimaker On the first note, it's impossible to tell, because even if you get 100 good prints off it, it might deteriorate irreparably from that point forward, for a number of reasons. Or you might just get lucky and it's as good as the UM2. On the second point, even the the Ultimakers are open source, it does not necessarily follow that commercialising their sou
×
×
  • Create New...