Jump to content

Marrut

Dormant
  • Posts

    33
  • Joined

  • Last visited

Everything posted by Marrut

  1. Heb dit ook eens voorgehad. Het gaat om die.gz. Als je dat verwijderd is het in orde. Als ik me goed herinner heeft het te maken hoe je de code opslaat. Je moet eens proberen met opslaan als en dan de goede extensie kiezen.
  2. Misschien hebben ze bij trideus nog rollen zonder nfc liggen. Kijk eens op hun webshop. Gr.
  3. Moet het echt pla van ultimaker zijn? Ik gebruik ice filament van trideus, van de zwarte en witte hebben ze zelfs grote rollen, scheelt heel wat tegenover ultimaker en print net zo goed als filament van ultimaker.
  4. Hi, Is the printer still for sale? Price? Witch country you are living? Can you send me a PM please? Gr, Martin
  5. Did I miss something? Are the STL files already available? I have read this thread a few times, but I do not find anything about the files. Just to know if I can start with the adjustments.
  6. Thanks for the reply RudydG I already have an olsson block, and customized cooling fans. So when I buy a feeder I'm done with it? Can I just update the firmware via cura to ultimaker2+?
  7. Hi, I was searching on the forum but I didn’t find an answer. Probably my method of searching is wrong. Is possible to upgrade my printer to a ultimaker2+ with only changing the feeder. Can I use the original main board and update the firmware to the ultimaker2+ ? If so, is it just updating the firmware to 2+ via cura 2.6….. or did I need to make modifications with the arduino software? Thanks in advance,
  8. SUPER!! this gonna be my next project in the winter.
  9. Ooops, thanks for the tip. I will download it this evening.
  10. Hi, Where can i download the 2.5 BETA 2 version? The downloadlink says versoin 2.5.1
  11. Maybe you can also take a look here https://ultimaker.com/en/community/39185-trying-to-get-better-underside-surfaces
  12. I do that in the drawing application. There's no possibility to do that in cura, but another question, witch version of cura do you use? If you have the latest version, than you have the possibility ti print "a roof" o' your support, that's almost the same as making an extra layer.
  13. maybe you can create an extra layer below the surface that has to be good. Most of the time i'm using an offset 0.1 à 0.2 mm, extrude it with +- 1mm and there under comes the support. normally you can peel it easy from the printed part. sorry for my bad english, i hope you understand what i mean.
  14. Hoi peggyb, bedankt voor de tip, maar werkt niet als ultimaker 2 als printer eselecteerd is. Als ik een ultimaker 2+ selecteer gaat het wel en krijg ik het gewicht. Als ik terug naar ultimaker 2 ga verdwijnt het gewicht. Lukt zo ook wel natuurlijk om de kostprijs te berekenen maar is met een omweg. Groeten, Martin
  15. Hoi, Ik werk met een ultimaker 2 en nieuwsgezind als ik ben, heb ik de cura 2.4 beta geïnstalleerd. In cura 2.3 kreeg ik naast de benodigde meters ook het benodigd gewicht te zien om een print te maken. (hoe ik dat voor elkaar gekregen heb weet ik niet) In cura 2.4 echter krijg ik het niet klaar om hier ook het gewicht te zien te krijgen. Wel als ik als printer de ultimaker 2+ selecteer, is dit een issue in de software? een instelling die ik over het hoofd zie, of is het gewoon zo dat het gewicht niet getoond wordt als ultimaker 2 als printer geselecteerd is? Groeten, Martin
  16. Vraagje, is onderstaande raspberry ok? Raspberry Pi 3 Model B Board+Heat Sink+Power Adapter AC Power Supply.Rasp PI3 B,PI 3 B,PI 3B.1GB LPDDR2 Quad-Core WiFi&Bluetooth Dan kan ik nog kiezen uit de RS version of element 14 version. Pakket is voor 39,50 € aan te schaffen bij onze Aziatische vrienden. gr, Martin
  17. @ ultiarjan, Bedankt voor de tip, ik ben niet zo thuis op dat gebied, maar ik ga eens wat rondneuzen op het internet en dan kom ik er misschien wel uit. Als ik het goed begrijp, dien ik een raspberry pi aan te schaffen en de software te installeren? of dien ik nog een extra besturingssysteem te installeren voor de raspberry? gr, Martin
  18. Hoi, Ik zou graag een camera plaatsen op mijn ultimaker 2 om zelf en anderen de print online te kunnen volgen. Zijn er hier nog mensen die dit doen? welke camera gebruik ik hier best voor? Zou dit gaan met een gewone IP camera die dan de beelden streamt via een server? Groeten, Martin
  19. Hoi, First of all, i want say that in my opinion the new version is great. But....would it be possible to get the function "multiple object" back. Now it's a lot of work to get several copy's together.
×
×
  • Create New...