-
Content Count
65 -
Joined
-
Last visited
Community Reputation
7 NeutralAbout Giogiogio4
- Birthday 02/28/1988
Personal Information
-
Field of Work
Education
(Product) design -
Country
US
- On The Web
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Sold
-
Giogiogio4 started following Cura bug? Brim is selected, Not printing,, Selling Ultimaker 2+, For Sale : Orlando FL USA. Ultimaker 2+ and and 3 others
-
$1500ish Model roughly has 1 month of runtime. Comes with door so you can use ABS without having to worry about the ceiling fan and air currents prematurely cooling and ruining you models. Includes 1 new roll of filament. A few nozzles A 1.75mm Conversion nozzle set Machine runs fine. I'm mainly selling because i'm focusing on my 3D skills and dont print anymore. So Id figure I would pass it to the next good owner. Attached photos are of most recent print. Wont do any test prints until serious buyer finalizes sale. ( I've already done an entire role of test prints for no shows ) Wont come with top cover due to shipping it would be too costly and I dont trust it making it through shipping. Orlando ,Florida Area available for pickup.
-
For Sale : Orlando FL USA. Ultimaker 2+
Giogiogio4 replied to Giogiogio4's topic in Buying or selling your Ultimaker
Then buy the ones off ebay? Seemed to have solved your own problem. -
Which software do you like to use to make models for 3D printing? At the moment im Stuck between Maya, Fusion 360. Sometimes I use 123Design to make quick things. Im unsure which program I should invest more of my time into. I have been using Maya, but I have been enjoying Fusion 360 much more layout wise.
-
Cura slices model incorrectly, unwanted holes
Giogiogio4 replied to Darth_Biomech's topic in Cura + plugins
Ok thanks! -
Cura slices model incorrectly, unwanted holes
Giogiogio4 replied to Darth_Biomech's topic in Cura + plugins
Was this issue ever fixed? I have been having it happen quite frequently -
Is Bed Adhesion really that much of a problem?
Giogiogio4 replied to Giogiogio4's topic in Help, Tips & Tricks
Havent tried Salt. I got tired of the glue method. Too messy and many times didnt really work or change anything. Florida here so it's very humid. printer is in my room so I tend to use the ceiling fan. My first prints curled a ton because of it. After I installed the door and cover all I use is tape. Cleaning takes maybe 2 mins? Just peel off and replace. 300 hours later I havent had a print fail. Sometimes I cant get my prints off the bed now XD Going to 3D and design a damn wall system that lets me put my glass bed against the wall and pull my prints off! -
Am I the only one who never has that problem? I think after the first week of owning my printing was the one time I had issues. I Don't use glue ever. Stopped using it because it was just a mess. I Just use Blue Painters Tape, a little bit of sanding and I'm done. My Prints always stick. I also installed a door and top cover to block my ceiling fan from cooling it down. If anything people should focus on cutting down on drafts in the area instead of throwing more glue down. No Issues with PLA on Painters tape.
-
Cura bug? Brim is selected, Not printing,
Giogiogio4 replied to Giogiogio4's topic in Cura + plugins
If anyone else has this issue. Didnt change anything. Disabled advance settings. Went back and my brims were back. Put back in the same settings and it seems to work. Don't know why resetting it seemed to do the trick. Before that rotating the model and rotating it back to the same position also brought them back. -
Cura bug? Brim is selected, Not printing,
Giogiogio4 replied to Giogiogio4's topic in Cura + plugins
Made a flat shape in 1234 Design. Exported it. opened it in cura. Rotated it 90 degrees so it was flat. Cura auto aligns it down to the bed. Doesnt have a first layer in layer view. Rotated it again long ways. It shows up. Rotated it back and it wont show up again. Very annoying. Its a simple RING shape. Didnt rotate it in the 2 other 3d programs I made it in. I made a cylinder shape. exported it and tried to open it in cura. Same thing. I started a print. It prints the brim. When the print fails I abort it and start it up again. The brim doesnt print on that file or anything else on the memory card. The gcode shouldnt change or lose layers just from sitting inside the printer. https://drive.google.com/file/d/0B1ya71IwpTg5UW5CVjRnR3gxUHM/view?usp=sharing https://drive.google.com/file/d/0B1ya71IwpTg5dGpsU290dDNRM3c/view?usp=sharing -
Cura bug? Brim is selected, Not printing,
Giogiogio4 replied to Giogiogio4's topic in Cura + plugins
Never touched the Brim settings since I got the machine -
I dont know what's going on. I have done about 13 hours of small prints this week. Same settings. Popped open my new 2kg roll of clear colorfabb xt and have had nothing but issues. First issue was simply the settings for this filament. To think the colorfabb color stuff that works great printing at temp 180-210 to this clear stuff needing to be at 240 and above... Anyways. for some stupid reason my Brim setting, which is checked and all within normal settings wont print! I noticed something was up when I first started a print and the printer even skipped making a normal parameter around where it's going to print at the start of the print. And it now wont print Brims...Which when you are printing a ton of small parts comes in handy!