Reflexx

Thanks Xeno, I'll try that. Have a good day. Regards,

Yes gr5, Printrun moves all the axes as I I command it to do.It also homes all of them at front left z=0. The temperature seems fine too. It comes up to 185°c within some minutes. Then I load a gcode on the platform( I changed the coordinates ( -55mm in x and y)of the head in order to center the object to print in the center of the platform, and a 3d model appears.then I click on "print" and the error message shows up and nothing more happens: Loading file: /Users/Myname/Desktop/tellit spejl plast.gcode Loaded /Users/Myname/Desktop/tellit spejl plast.gcode, 3151 lines 23.52mm of filament used in this print The print goes: - from -55.00 mm to 8.71 mm in X and is 63.71 mm wide - from -55.00 mm to 8.70 mm in Y and is 63.70 mm deep - from 0.00 mm to 15.00 mm in Z and is 15.00 mm high Estimated duration: 26 layers, 0:01:26 Print started at: 08:05:58 [ERROR] Failed to set power settings: Traceback (most recent call last): File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.pronsole", line 1173, in startcb File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power", line 130, in powerset_print_start File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 72, in inhibit_sleep_osx File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 49, in AssertionCreateWithName File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 40, in StringToCFString AttributeError: 'module' object has no attribute 'kCFStringEncodingASCII'

Hi gr5, I've tried several times to print, both with Cura, and also with Printrun. But after having loaded a gcode file, Cura doesn't react at all to my printing command. Printrun seem to react with an error code in the console. It says: Print started at: 22:02:50 [ERROR] Failed to set power settings: Traceback (most recent call last): File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.pronsole", line 1173, in startcb File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power", line 130, in powerset_print_start File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 72, in inhibit_sleep_osx File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 49, in AssertionCreateWithName File "/Users/craigvanvliet/Desktop/PyInstaller-2.1/pronterface/build/pronterface/out00-PYZ.pyz/printrun.power.osx", line 40, in StringToCFString AttributeError: 'module' object has no attribute 'kCFStringEncodingASCII' I found some refernece to the same problem on: https://github.com/kliment/Printrun/issues/619 but they didn't seem to have resolved the problem. Would it be better to buy an Ulticontroller? Regards, Reflexx

Thanks a lot gr5. I 'll try as you say and give you a feedback. Have a good day!

hi Ultimakers, I'm a newbie, and just bought a probably 3-4 years old Ultimaker Original. It has a custom made heatbed in a hexagonal shape, and no Ulticontroller. It is connected by USB to my Mac, and Cura seem to work fine, the motors are ok, the calibration wizard also works, but my custom made buildplate doesn't seem to match the head positioning: it always uns to the front left corner and waits for me to level my buildplate, which is several cm away. Of couse it's because the normal build plate is square and bigger than mine. I do not know how to configure the shape of my custom buildplate.. that's one question. The second question is: can I print without Ulticontroller? I've read a lot of posts about that, and it seems possible, but could have stability issues regarding communication with the computer. I lauched Cura with pronterface UI, and the head is heating fine, and the filament is beginning to melt, but nothing else happens. No print. Does anybody have an idea what I should do?