Jump to content

jeracom

Dormant
  • Posts

    66
  • Joined

  • Last visited

Personal Information

  • Country
    DE
  • Industry
    Engineering

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

jeracom's Achievements

4

Reputation

  1. for Ultimaker 2 or 2+ I think.... I wanted to separate the printer room temperature somewhat from the stepper motors. That's why I've made shelter housing for it. Left Side and Right Side But I also cut holes in the back for fans and put the air out of the top. Of course you do not need that. 🙂 https://www.thingiverse.com/thing:3483511
  2. Hab noch ein Um2+ liegen. Da ich Bondtech drann habe...
  3. ITX case for 6,7 × 6,7 Zoll boards (Case 19cm x 19cm x 7,7cm LBH). Print in PETG, of course you can also take something else 🙂 . It took me a moment to get everything right. The rear panel also fits now. The kit consists of housing, the housing cover.(in DIFFERENT VERSIONS) The front panel, made of two parts, and the associated buttons with the back brackets for the PC switches. Front panel, two versions with magnet or with metal pin. Front On Off, open, closed LED cover. Front panel, buttons, magnets I glued with 2K glue. Below the board is a HDD-bag that can hold two 2.5 Zoll disks. Under the board is also an M2 slot. In addition two fan grille, which I covered with insect screen. There is nothing screwed except the motherboard. The rest is fixed with Neodym magnets. Also easy to open. I take a 35 watt CPU Since I work with electricity, I take no warranty Sata cables etc ... I have used the following parts: Ich habe folgend Teile benutzt: PC Reset Schalter Kable ATX Power-Reset HDD https://www.amazon.de/gp/product/B07BT3ZZ8X/ref=ppx_yo_dt_b_asin_title_o05__o00_s01?ie=UTF8&psc=1 Thermaltake Engine 27 https://www.amazon.de/gp/product/B01M4J64GU/ref=ppx_yo_dt_b_asin_title_o06__o00_s01?ie=UTF8&psc=1 LEICKE Netzteil 120 Watt 12V https://www.amazon.de/gp/product/B006Z9TQE6/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1 PicoPSU-150-XT 150W 12V DC-DC ATX Netzteil https://www.amazon.de/gp/product/B0045IXKTQ/ref=ppx_yo_dt_b_asin_title_o06__o00_s02?ie=UTF8&psc=1 Neodym Magnete 10x2 mm https://www.amazon.de/gp/product/B06X977K8L/ref=ppx_yo_dt_b_asin_title_o07__o00_s00?ie=UTF8&psc=1 Find on Thingiverse https://www.thingiverse.com/thing:3409531 Ultimaker 2+ Resolution 0,2 Infill: 35% Print in PETG
  4. jeracom

    Error stopped

    Nein hab den Gcode leider nicht mehr 😞 Wie gesagt neu geslict und ging. Hat Tatsächlich laut Grafik kurz 4 oder 5 Minuten ausgeschaltet, Nozzle und Bed. Danach wieder Temperatur. Octoprint stand danach natürlich auf "Pause" Modus.
  5. jeracom

    Error stopped

    So, Druck hat knapp 8 Stunden gedauert und ist einwandfrei durch. Wie in Octoprint oben zu sehen ist offensichtlich, meine Vermutung jedenfalls, der GCode nicht OK gewesen. Soll Wert der beiden, Nozzle und Druckbett war auf null. Ist Wert fiel natürlich langsam ab. Dadurch wahrscheinlich der Error. Drucker Neustart , Octoprint Neustart, Teil neu Slicen und der Fehler taucht bis jetzt nicht mehr auf.
  6. Ich gehe davon auch aus, das die Glasplatte auch nicht ganz eben ist, war bei mir der Fall. Seidem ich die Alu-Pei habe, mach ich ab und zu eine Druckkopf Ausrichtung und fertig. Alles ander klapp wunderbar...
  7. Ansonsten fällt mir ein, die Glasplatte mal gegen eine Pei-Alu zu tauschen. Bin auch weg von Glas und seit dem keine Probleme mehr. Sowas hier z.B. https://clever3d.de/PEI-Dauerdruckplatte-Aluminium-Guss-feinstgefraest
  8. Gibt es sowas wie "Verticaler Hub des Einzugs" auf Englisch Retraction Vertical Lift ? den mal dan auf 0,40 setzen!? PS:Ich benutze S3D
  9. jeracom

    Error stopped

    Alles neu gestartet, nue mal geslict und bis jetzt läuft es... Scheint tatsächlich einmalig gewesen zu sein.
  10. jeracom

    Error stopped

    Ist mir eben im Log aufgefallen. Scheint wohl ein wackler zu sein. Kurzeitig war das Heatbed nicht messbar, so wie es aussieht. und auch das Nozzle. da es die Soll kurve ist die da abfällt, kann es sein das es auch ein GCode Fehler war. Ich slice noch mal neu und schaue was passiert
  11. jeracom

    Error stopped

    Seit Ewigkeiten Wlan, Raspi, und Ocktoprint. Die USB und SD Karten Fehler habe ich am Anfang schon durch 🙂
  12. jeracom

    Error stopped

    Hallo mal kurz eine Frage. Der UM2+ Hält im Druck an, und sagt "Error stopped" Nix weiter, wie Header error oder was auch immer. Nur Error Stopped. go to Ultimaker.... Temperatur Nozzle und Bed haben immer noch die eingestellte Temperatur Sowas schon mal gehabt?
  13. So ist zwar schon ein wenig her, aber meine Lüfter beim UM2+ haben sich auch zerlegt. Zu blöd nicht aufgepasst und auch Kurzschluss. Der Code oben im Bild darauf, 6BW soll der Marketing Code sein 52 ist die Herstellugs-Jahr und Monat. Also 2005 im Monat Februar. Ich habe mir folgende bestellt da es nicht so häufig, zumindest hier in DE welche mit 800 mA gibt: BC817-40 NPN 45V 800mA 310mW SOT-23 mal sehen ob das funktioniert.
  14. Das ist schon klar. 🙂 Nach fest kommt ab....
×
×
  • Create New...