Smokie
Dormant-
Posts
33 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Everything posted by Smokie
-
Hoi Greg,if turned all back to 4.13 But mabay later ill try 5.0 again and look at these setting Fore now thanks Wr Henk
-
Hello Greg, mostly by sd card But in 4.13.1 the problem is gone Wr,Henk
-
cura5.0 pauses at random times, moves to a position next to print and resumes print after +- 15 sec got an ender 6 , then back to 4.13.1 and problem solved wr,Henk
-
cura5.0 pauses at random times, moves to a position next to print and resumes print after +- 15 sec got an ender 6 , then back to 4.13.1 and problem solved wr,Henk
-
hello Nallath thanks fore respons have upgraded windows home to pro maby there is the problem wil try to update the drivers wr Henk
-
Hey I use cura 4.11 on 2 Pc's a Toshiba tecra and an HP Pavilion g6 on the Toshiba the "preview mode" after slicing works as I was used to with right and under a slider so you can simulate the print on the HP, however, the lower slider bar is missing and there is only a slider bar on the right side I have already tried several times to reinstall and also an older version has the same result, it is probably in my HP PC but where to look? please response mr Henk
-
-
hello diving duck thanks fore the reply i have tried already some things my qu are : must i do this in the new cura version how to do this so i dont have to do it every time again maby a bit stupid but i cant get it working wr Henk
-
hello i would like to use the same start g code as in cura 3.10 in the newer version(s) 3.6 or 4.0 how to do this? wr Henk
-
found an old post that pointed me in the right direction https://community.ultimaker.com/topic/19494-circles-are-not-fully-round/ my x / y frame was not 90 degrees square have tacled this with braces and the print result is finally good w r Henk
-
Well, if changed the stepper but no(the same) result Dont know were to look now for a sollution? Wr Henk
-
have checked every bolt a more closer look shows a mistake in the print direction at 4 places see image now i think that the y axis stepper motor skips steps at direction change have ordered a new one fingers crossed?
-
Hello I have simmelair problems Wonderd if and how you solved the problem Wr Henl
-
Thanks for the reply John printer wanhao duplicator v2.1/ 0.4 nozzle/ PLA /Cura 3.1 0.2-brimm 0.8-wall 0.8-top/b0.8-comp wall overlaps-hide seam-infill 20--retr 1.5-cooling-speed 60 mm/s pos see picture im chekking belts/stepper report back if there are results wr Henk
-
-
-
All interesting options to try but my problem is how to upgrade to the new cura version(s) and resulting in a better print Wr Henk
-
I know PC does and is recommended. Hello Started with 16.0.1(black) has a raft/brim option Than 15.04.6 also After that 2.6.2 and 2.7 with al kind of options Normal a raft gives me the best result with sticking to the bed but with bad bottom result The skirt option in 2.7 works fore the bottom (in custom mode) Wr Henk
-
-
That looks horrible.... Was that a default um profile? Yes in both versions Fore me its still a puzzle why every new version looks to give a worst result Wr Henk Do you have a link to the model? hope this link works:https://www.dropbox.com/home?preview=bus.stl wr Henk
-
That looks horrible.... Was that a default um profile? Yes in both versions Fore me its still a puzzle why every new version looks to give a worst result Wr Henk
-
struggling struggling:( to much possibillities isnt always resulting in a better print left 2.7 rigth 15.04 long way to go fore me! wr Henk
-
Hello Cant open GCode generated in version 2.6.2 with a simulation progam Wat am i doing wrong? Wr Henk
-
After 1 1/2 week of problems finally printing with a good result!! Was drawing the reeds in 123design all from start and saw the options 1)to show the part 2)part with constr lines 3)constr lines only Never paid notions to that but i tried the option 1(part only) After that saved the stl and conv to g code in cura The g gode in a simulation showed a good print and the real print was now also with a good result without allthe problems of the last week So i think the constr lines were the problem in conversion with cura Wr Henk
-
tried all that,but no result can't reed the G code but i think its what you say ,pussing too much fillament from layer 5 and further but there is no fillament comming out will experiment futher thanks fore the support wr Henk