[unwanted line on first layer]

thanks

work fine !

[unwanted line on first layer]

16 minutes ago, NBull said:

Try setting "combing mode" to (not in skin)

enable: 

Avoid printed parts when travling

Z hop when retracted

Z hop only over printed prat (not sure if this is needed but i have it on)

 

 

   

 

 

 

[lignes indésirable première couche plaque]

On 11/15/2018 at 7:30 AM, DidierKlein said:

Même réponse que dans un autre sujet:

 

C'est dans Travel -> Combing -> Avoid all (il me semble)

 

Dans la vue layer tu vois les mouvements de déplacement en bleu

merci -> combing mode off 

fonctionne

[unwanted line on first layer]

Hello 

Is there Cura settings to avoid line on first layer (see attached)
thanks

[lignes indésirable première couche plaque]

Bonjour

Comment régler les paramètres Cura pour éviter ces lignes parasite (voir photos)

Que j'imprime en ASA ou ABS c'est la même chose 
merci

[Problème Adhérence plateau équerre ABS]

bonjour

- j'ai une enceinte fermée

- température indiquée sur la bobine 220-270 °  

- ma pièces fair 100x100 mm

 

merci 

[Problème Adhérence plateau équerre ABS]

 Impression d'une équerre ABS . Les bord se décollent et se soulèvent  du plateau .

 j’ai essayé avec plusieurs réglages remplissage : 50% ou 75 % , température d'impression ABS 230 degrés ou 250 degrés …adhérence au  plateau sans / avec Raft , 

- température du plateau 100 degrés - 

rien n'y fait !!!!

 

[unwanted lines on surface]

thanks for the help have a nice day

[unwanted lines on surface]

i did a another one :

https://www.mediafire.com/file/slyuf55nc99hhwa/UM33_plaque110_project.gcode

[unwanted lines on surface]

hi

https://www.mediafire.com/file/w86nn646d3re1uy/support.gcode

thanks

Claude

[unwanted lines on surface]

Good news the text is nice with out scratches

Thanks a lot for the help

P.S

A small retraction off the character V subsist

(if not really important but if you have a idea ? )

rgs

[unwanted lines on surface]

I send a print with combing OFF, I'm coming in touch tomorrow

rgs

[unwanted lines on surface]

sorry

https://www.mediafire.com/file/w86nn646d3re1uy/support.gcode

[unwanted lines on surface]

Dear Mark

See the

I'ts much better but black lines subsist over the text , it's too bad

gcodes :

https://www.mediafire.com/file/r32pxv6byj0w61d/UM3_plaque_et_text_220v.gcode

[unwanted lines on surface]

Retract before outer wall is in custom settings -> travel

Outer before inner walls is in custom settings -> shell

To see these preferences you may need to go to Menu settings -> configure setting visibility

Cheers,

Mark

 

[unwanted lines on surface]

hi, really thanks a lot for helping I will try tomorrow

where is the setting : retract before outer wall enabled and print outer wall first enabled

Have a nice we

claude

[unwanted lines on surface]

thanks

https://www.mediafire.com/file/r32pxv6byj0w61d/UM3_plaque_et_text_220v.gcode

[unwanted lines on surface]

thanks

I tried but is not better there is still a black line under the red text

[unwanted lines on surface]

hi

how to resolved the unwanted lines on surface ? see pictures

thanks

[Solidworks macro Export to Cura 2 not working]

Hi

I get the message : I cannot find cura on this computer

Macro : Export_to_Cura_2.x.swp

Solidworks : 2016

Cura : 3.0.4

Thanks

CEP