Jump to content

klaus_kraemer

Member
  • Posts

    50
  • Joined

  • Last visited

Everything posted by klaus_kraemer

  1. Gestern bestellt, heute schon eingetroffen - das nenne ich schnell. Jetzt bin ich am auseinanderbauen. So ein wartungsunfreundliches Teil, dieser Druckkopf ...
  2. @Graby: Bei mir ist auch das rote Kabel abgebrochen. Ich würde mal sagen, das ist eher eine Fehlkonstruktion ... Frage: Hast Du den Druckkopf ausgebaut, um das zu reparieren? So scheint mir das rote Kabel zu kurz zum Abisolieren und Löten.
  3. In another thread I stumbled over this: @GregValiant mentioned: His proposal had been to use "Hole Horizontal Expansion" to compensate for this phenomenon, which is nor useful, as soon as a lot of different hole diameters appear in a single print. Wouldn't it be a solution to print inner diameters very very slowly? This could be another approach feasable with CURA...
  4. I suppose your question addresses V4.9.0 too?😏
  5. I'd really expect to address this annoyance immediately...
  6. Wieder was gelernt - klingt recht nachvollziehbar. 👍
  7. Danke für die Info! Hab' gerade ein Teil laufen und die Temperatur auf 200° abgesenkt, Lüfter voll ab 4. Schicht, 7mm Retract bei 45 mm/s. Mal sehen - an höhere Drucktemperatur hätte ich mich erst mal nicht getraut, nachdem ich das Gefühl habe mit der 0,8er Düse läuft da leicht noch was nach - aber deshalb frage ich ja auch erfahrenere Leute... Gruß, Klaus
  8. Ich find' das Material auch Klasse von der Qualität, wäre jedoch sehr an Deinen Einstellungen dafür am Ultimaker interessiert, denn Du brauchst das für den Modellbau sicher optimiert. Wärst Du so nett, die Einstellungen mal zu posten? Mit den PLA-Einstellungen für original UM habe ich bei kleineren Strukturen immer mal Probs mit Nachtropfen bei kleinen Strukturen, zwischen denen schnell gewechselt wird, da streift er dann Material beim Anfahren der Struktur ab. Ich versuch's mal mit geringerer Temperatur un schnellerem sowie weiteren Materialeinzug. Danke schon mal Klaus
  9. Adaptive layer thickness seems out of bounds: As a base thickness I had chosen 0.1mm. Ok, so maximum thickness should be 0.25mm, according to "Adaptive Layers Maximum Variation", isn't it? But why 0.53 mm for the brim then? Minimum thickness seems to shrink below the Ultimakers' specification of 0.06mm - 0.01mm is to small. Why isn't minimum thickness set accordingly to the minimum layer thickness of the Ultimaker? Yesterday I ran into the same problem with another part. As a result the nozzle began bathing in filament. Luckily that happened at the 6 top layers, so I could save the job with a box cutter....
  10. I think it's a good first step: But why stop midways and stay inside the interface instead "Drag and reposition panels everywhere in your desktop? With multiscreen environments becoming more and more ubiquitious, why restrict panels to the interface, where they will always hide some portion of it?
  11. So far: It's better now and you showed me a new approach! Thank you!
  12. Thank you @smartavionics! I'll try your suggestions tomorrow morning. In the meantime I had also switched to a 0.4 mm nozzle. The hole has 1.7mm diameter instead of 2.4mm (I had it slightly widened before trying the new print). Best regards Klaus
  13. Hadn't known the project file would help - here it is: UM3_Ohrreinigungsduse - Ohrreinigungsduse.3mf Thanks for trying to help!
  14. I have built an adapter to mount on a syringe. Its hole width at the top should be 2mm in diameter. CURA shows the hole and the dimensions seem to fit: When this adapter is printed with a 0.8mm AA nozzle, the hole in the tip simply does not exist! The adapter is air- und watertight! I have experienced that they always tend to be too small -- but there is a real leap between 2mm and solid airtight Is there a way to achieve exact inner hole diameters?
  15. A little bit crude - always a chance of tearing off part of the filament inside the extruder. I'd rather treat machine and filament gently...💪
  16. Filament change: I just experienced a weird situation, when I wanted to change Willowflex filament (a flexible one) for normal PLA. As friction of Willowflex against the Bowden tubes is higher, Willowflex is not totally removed from the Bowden tube and the extruder. The only option UM3 firmare offers ist to confirm, the filament to remove has been removed - nothing else, silly! There has to be an option to move filament manually until the filament is really removed or at least an option to end the filament changeing procedure. That way you could use the menu to get to the point where you can move filament manually.
  17. Thank you @drayson, but I simply wouldn't know how to use that code... The more I think about it, the more I feel that Cura Connect should provide extensive information about the current print job. Let's wait and see...
  18. I imagine, it is the only way I can monitor print and decide when I have to control whether some special or critical part of a print works out. Its mostly about deciding whether to cancel the print or not at that point. I've spent to much time in front of the printer, waiting for certain parts to be printed - unnecessary wate of time due to lack of information. I can easily get the layer number from the layer view in Cura. Other ways of avoiding that issue would be a more detailed information via Cura connect web interface, which is simply one of the poorest I can imagine... indicating a time in Cura's layer view, predicting when a single layer will be printed before completion of the whole print. So you could always compare with the remaining time for printing on the UM's display. The solution does not necessarily have to come via the printer's display, it could also come from Cura's web interface. From another point of view: Indicating the remaining time AND e.g. 'Z 1000/1784' wouldn't be so difficult and bad...
  19. Any clue this feature request got into the next firmware release?
  20. Just saw that possibility - thanks for the hint! But anyway - the popup is annoying and unprofessional...
  21. This happens way too often to be solved with a workaround only!
  22. Every time, I try to download a CURA update, a popup form starts asking me the same boring questions. I really don't like redundancy and I'm logged in. So why are you asking the same questions again and again? Until now I've answered these question to my best knowledge. For the future I'm tempted to simply click some items from the menu to get the update downloaded. Will that random and wrong data help you in any way? I don't think so - but you don't seem to be really interested in that data, otherwise you'd keep them in a dataset under my account. I am quite sure, many users simply click something to get forward and I'll join them...
  23. Quite hard to believe there shouldn't be a way to get around this behaviour. Ok there's no printer driver for UM3 as far as I know, But continually testing an IP connection should be feasible anyway...
×
×
  • Create New...