Jump to content

niamor2

Dormant
  • Posts

    10
  • Joined

  • Last visited

Everything posted by niamor2

  1. Thanks a lot ! For now I will try putting the spool in an airtight pouch with dessicant for several days. If that doesn't work I will try the heated bed.
  2. Ok merci, j'avais déjà fait des impressions pendant plusieurs jours en laissant ma bobine à l'air libre sans avoir eu de souci jusqu'à maintenant... mais je vais me renseigner !
  3. Donc il faut ranger la bobine dans son sachet après chaque impression ?
  4. Thanks for the advice, but I already removed the bowden tube, and I couldn't remove the filament no matter what. So I tried your last solution, and here is what I found : I don't understand how that could happen, but it seems the filament folded inside the feeder... explaining why I couldn't remove the filament manually ! So I finally extracted the filament successfully, and launched a print with a new PVA spool : everything seems to work properly ! Conclusion : NEVER try to print with a PVA spool that remained a long time in the open air !
  5. Merci pour vos conseils ! J'ai donc démonté le feeder, et voici ce que j'ai trouvé : Je ne comprends pas comment ça a pu arriver, mais il semble que le filament se soit replié à l'intérieur du feeder... Il y avait donc 3 épaisseurs de filament passant par le feeder, pas étonnant que je n'arrive pas à l'extraire manuellement ! J'ai donc finalement réussi à extraire le filament, j'ai remonté le feeder et j'ai lancé une impression avec une bobine neuve de PVA, et tout est apparemment rentré dans l'ordre ? Je vais tenter de récupérer l'autre bobine en la laissant dans un sachet fermé avec du dessicant. Conclusion : ne JAMAIS lancer d'impression avec du PVA laissé à l'air libre pendant un mois !
  6. Yes I tried but it didn't change anything. Squeezing the lever or not, thye filament remains stuck...
  7. Hi everyone, I'e got a serious problem with my last print with PVA on my Ultimaker 3 : the material stopped extruding after 1hr, and while trying to unload the PVA filament I realized it was stuck in the feeder. Then I removed the bowden tube at both ends, removed the PVA filament from the printhead, and cut the filament under the feeder. But I still couldn't remove the filament, whatever side I pulled on : I guess that might be caused by a degradation of the filament by ambient humidity : the spool was left out in the open air for more than one month. But I still don't know how to remove the filament from the feeder. May be I could try moistening the filament in the feeder to soften it and remove it more easily ? Or will I have to disassemble the feeder completely ? Any ideas ? Thanks !
  8. Bonjour, Je pense que votre message aurait plus de réponses dans la catégorie des messages en français. Bonne journée
  9. Bonjour à tous, J'ai un gros problème concernant ma dernière impression avec du PVA sur l'ultimaker 3 : l'impression a cessé d'extruder après plus d'1 heure d'impression, et en voulant retirer le filament de PVA je me suis rendu compte qu'il était coincé dans le feeder. J'ai ensuite retiré le bowden tube des deux côtés, puis retiré le filament de la tête d'impression, et coupé le filament en dessous du feeder, mais malgré cela et en tirant dans les deux sens, impossible de faire bouger le filament : Je suspecte que ce phénomène pourrait être dû au fait que la bobine est restée à l'air libre pendant plus d'un mois, le matériau a pu être dégradé par l'humidité ambiante. Toujours est-il que je ne sais pas comment me sortir de là. Peut-être que je peux essayer d'humecter le filament dans le feeder pour le ramollir et l'extraire plus facilement ? Ou faut-il que je démonte entièrement le feeder ? Vous avez des idées ? Merci d'avance !
×
×
  • Create New...