Jump to content

Arturas

Member
  • Posts

    37
  • Joined

  • Last visited

Everything posted by Arturas

  1. thank you for your replay. I would agree with cable issue, but how come sensor too low or too high? if is in same position always?
  2. HI, I do have issue with auto leveling in ultimaker extended. 1 of 3 times is OK, but other 2 times keeps getting this message. please see pix. Its happen in very beginning of leveling. First ultimaker measure 2nd head, and once it starting move z axis for 1st head it give that fault. but bed has not even touch bed. Hoe to fix or what is the reason ? Thank you
  3. HI, Could you explain why its happening, print started smaller scale and after get slightly bigger, i hope you it can be seen on picture
  4. Also i notice 3D solex core is not working well as well. It start printing all good, but after 30 min or more filament is blocked. Printer shows 200 degree but filament is not extruded. so i took print core from slot 2. swapped with slot 1. That original core is printing with same setting and same filament well. So what is wrong ? temp sensor or heat element in core? I checked temp sensor ohm is about 110.
  5. Hi, Could someone tell e why its fails? Heat cartridge is broken? Also what does mean delta T 20 degree? whats mean i should add 20 degree more on filament sensor ? Thanks
  6. yes sound same , auto leveling can get right height. i did manuly and switch off leveling. it works until i will have to change a core or one of heads.
  7. sorry for later replay, Yes i am running latest software, and would say its happens after update. Automatic leveling not working right at all. if i change head size and let do auto leveling, it will get wrong level, head scratching glass. If i do manual leveling , and switch off auto leveling, it keeps ok until i change head. my understanding auto leveling should get right level itself but it not happening.
  8. how come after automatic leveling 2nd head scratch a bed? its no gap at all. if i did manual leveling as you said 0.1 still nothing. is it possible somehow get in printer to read saved settings for leveling? why it keeps head so low.
  9. hi, I dont understand my printer. i do have Ultimaker 3. I do manual leveling as its asking, 1mm after final calibrating card. after manual leveling i turn rising bed, and its hits 2 nd head no gap between. lets say i choose automatic leveling still hits head after rising bed, what ever i do , its start printing to close, head scratching glass so how to get sorted?
  10. its happening to me as well. filament get blocked in feeder. I event change DDG fedder with 1.75mm gears and still same issue filament not getting extruded from core, or its getting little bit and stop again.
  11. Hello, I would like to ask someone who could give gcode to put in to cura. I need to check filament length being pushed by DDG feeder, so i want to make a mark on filament 10cm above core. i will take start point from tube. So i need right a code in to cura extrude 10 cm filament before its starts print anything, also i need lower bed little bit for this 10cm . Can some one right a code please 🙂 Thank you
  12. have change seeting in cura? you need change printer filament from 2.85 ro 1.75mm as well and after slice it
  13. i found out what is bontech 🙂 so what about core? is nozzle size is no matter?
  14. chuck-yanke Who is GR5? user ? And who is Bontec? 🙂 sorry i dont know do you think is only feeder has to be change? what about head? the hole size inside is about 3mm? is not to big ? Thank you
  15. all issues sorted after new cura released
  16. Hello, I know that story about size filament is old and many topics about it. But i still can not understand why can not be made new core just for 1.75mm filament. after new core i believe its just software setting need to made. why not to give a option for people who is interested in it. I am ready to pay few hundreds just to have option to print 1.75mm size filament.
  17. i very happy, i am getting very well results, and this Teflon tube can be take off no problem. it give option to used 2.85mm filament again if needed.
  18. sorry for confusing message. question was is it possible resume print after power fails, without any code editing. anyway thank you for replay.
  19. Hi, Printing from usb, after power fails ultimaker3 no option and its not resuming to previous print? Thank you
  20. Hi, I would like to share with you how i make few updated on ultimaker3 to use 1.75mm filament with no more blocking inside hot end. Before filament keeps blocking my hot (print coore) end event feeder was working fine, event original bowden is big enough. So i left everything original no cuts no changes on printer itself. Only I add extra 2x3mm teflon tube inside print core to reduce that original hole. I put all way down as much as possible and left short end. One more changes i did its in cura itself. changed filament settings for each core. go to machine settings>extruder
  21. Brulti, Autocad, before you slice object , object has gravity center individually, after you slice in two ore more parts, each part has individually gravity centers. when you transferring all parts in cura i can i alight two coordinate to match. But one of (x,y) i don't know to mach in one peace. it could be 0.01 different and it wont be one big peace.
  22. fusion 360 is just demo version i do have, unless you have link full version
  23. Hi, Could someone tell me why its happening and how to make good. I trying to merge to part in one to print two colors but its merge me wrong as should be. I cut in two peaces with Autocad. but how to set up cura to merge right? Thank you
  24. Hi, After new version of cura 3.5.1 i start getting problem with slicing. part to print it so small but it says its nothing to print or non model to fit. I have to restart cura to get working until its comes up again Thank you
×
×
  • Create New...