greatg
-
Posts
27 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by greatg
-
-
I'm selling my S5 Pro bundle and was wondering what needs to be done before it goes to new owner? Do I just do a factory reset and that's it?
-
I'm selling my S5 Pro bundle because it hasn't been getting much use since purchased. Printer has been maintained as per Ultimaker PM schedules. I live in Ontario, Canada. Asking $12,000 (CND) for the entire bundle with local pickup (no shipments). I live near Niagara Falls (near by US accessible).
Bundle includes:
S5 Printer
Material Station
Air Manager
15 un-opened 2.85mm filament
8 additional print cores
-
Since upgrading, have noticed that the display will not go into sleep mode. Stays on all the time when the printer is not in use?
-
On 1/27/2021 at 4:32 AM, robinmdh said:
Hotfix 6.1.1 is on the way for the issue we've identified, pending tests and approval.
In some rare cases corrupted material profile files where giving problems and a small change in python's xml.etree.ElementTree library meant this caused the application not to start up.
As a workaround you can turn off Cura and "reset all printer settings" in the settings menu before upgrading, that will allow you to install the 6.1.0 without the current problem.
In the mean time if you have already gotten stuck at the logo screen, please open a support ticket as @SandervG said!
Use the 6.1.0 recovery image not a 5.x or older one! as mentioned a lot before 6.x can't be downgraded, this can brick your printer in a not user recoverable way.Hello, was the hotfix ever released?
-
My problem was a faulty air manager. Wound up returning it to the dealer in exchange for a new one (after working with Ultimaker support to troubleshoot)
-
On 10/9/2020 at 4:42 AM, A_tas said:
Hello all,
Yesterday we update our UM S5 with latest Firmware 5.8.1.
After that we observed the following problems:
1. There is not connection between the the printer and Cura. We checked with our IT colleagues - there is connection between the printer and the PC (ping). When we try to refresh the printer in Cura - this screen appears for about 5 seconds and disappear.
S5 cannot print from PC (Cura 4.7.1)
S5 can work (print) with USB.
The camera is not working.
S5 can work (print) with USB. The Camera is not working.
2. After firmware update , appear ER 67 . We never experienced this issue before. The material station is less one year old. We follow the instructions regarding the ER 67 from the UM site - no result. The error appears again.
Please, help me to solve this problem.
I red that the firmware 5.8.0 has problems and wait for the release new firmware with fixes problems. It seems there are still any.
Updated todaY to 5.8.1 - get the same humidification error
-
-
Still having major issues with the PVA loading. Now it appears that there are gouges in the filament as it tries to load. Never reaches the extruder.
-
On 1/30/2020 at 7:32 AM, SandervG said:
Hi @greatg, thank you for sharing your experiences.
Could you share a picture of the tip of your filament that you are trying to feed? Is it pointy so it is unlikely that it will grip behind anything?
You're saying that you get an error before the filament reaches the feeder on the S5 right? Does it exit the decoupler?
Hi @SandervG, The filament is clipped at a 45 deg. It does exit the decoupler and then never reaches the feeder. I usually have to manually pull the filament out and feed it through the feeder, along with a few more error codes and power pulls...
-
Did the hot pulls and swapped the core. Will have to have a look at the tension of the feeder. What seems strange is that without the material station loading is not an issue (not feeder problem).
-
On 1/27/2020 at 5:45 AM, SandervG said:
Hi, thank you for your message. The profiles for materials supported in our marketplace are being actively worked on as we speak and should be made available in batches in the near future.
Exactly because of these reasons.
Hi @uncle_bob, I would be curious to get more information on why they don't work or what makes you think why they don't work. We would love to help you.
Hi, can you elaborate on what is happening why it does not reach the print core? As Uncle_Bob said, the Material Station is more aimed at keeping your material dry, instead of drying it when it is wet. Depending on the shipping conditions or what happened to the material before it was packed or inserted in the Material Station, it could be worth your while to dry it before loading it.
So,I have purchased 2 new spools of PVA from local dealer, and I dried my existing spools using the Ultimaker suggested process. One of the new spools loads OK. Print starts and runs for 4 hrs. The I get an error 56. Have to pull the power plug to clear the error and the I have to manually remove the filament as the unload feature is grayed out. That's another failed print. Next I try my dried filament. Run the load sequence and get Error 57. Pull power plug, try different bay, loads but doesn't reach extruder. During the priming process no material is extruded unless I apply force to move the filament along. This only works for a few seconds an another error 57 pops up. When reverting back to original S5 sans material station, PVA loads and prints OK. Sometimes I get message that the filament has run out? Seems like PVA is a real PIA!!
-
1 hour ago, nickp100 said:
I wish the one that I mentioned earlier was the only problem with this printer,( as I was able to print anyways). The Air Manager is a complete and utter brick. Even though it shows installed under maintenance the actual fan never kicks in. As a result, with the hood closed it clogged a brand new print core with filament. Even after we decided to print from then on with the hood open, we have had a myriad of issues with the material station. About 60% of the time the filament never makes into the print cores, and has to be fished out. In our current situation filament is stuck between the lower decoupler (which is now stuck and cannot be removed) and the material station.
We in the process of filing all those issues
All that seems like this machine was never meant to be released at this point and we all are beta testing for free!
Extremely dissappointed with this "pro" bundle
I had a similar issue with the air handler. Had Ultimaker tech support help out. The only solution was to replace it under warranty. A defective unit was the tech support conclusion.
-
I've given up on the material station! When I went back to the "old" S5 set up, the PVA material loaded without any issues! I think the material station is a good concept, but not ready for the real world!
On a side note. I primarily print PLA. What are my options for other support materials besides PVA?
-
I'm having a heck of a time with PVA printing properly. I have 2 spools of PVA that were recently purchased. I let them sit in the station for 3days. Most times the filament never reaches the print core. Is there a way to manually prime the filament?
-
OK. So, the material station works. As soon as I plug in the air manager I keep getting the error that the fan cannot spin to speed? There are no obstructions, firmware updated to latest, filter taken off fan...
-
OK. So, the material station works. As soon as I plug in the air manager I keep getting the error that the fan cannot spin? There are no obstructions, firmware updated to latest, filter taken off fan...
-
So, All was good for about 12hrs and then the message "Air manager fan was unable to rotate at the desired speed. Go to ultimaker.com\ER57." I tried to unload the filament, but the selection are grayed out. No response from the station?
-
Have you hooked it up to your UM2+?
-
Looks wonderful! What are you using to scan the models? I'd like to make some busts of my children, but not sure how to proceed.
-
If you are plugged into a network, unplug and restart the printer. I had the same issues. Took it back to dealer and could not reproduce the fault.
-
Just wondering if the mobile app will allow for connection when not using the same network? I just tried and it did not work?
-
Excellent question. I have the same issue?
-
Recently, the S5 has been having a strange issue where the material just doesn't want to come out of the core. I can load the material, the nfc recognizes it, and at the end of load a nice clean string is extruded. But, when I go to print, nothing comes out? I have to manually, give the filament a little push for the extrusion to start? This never happened before?
-
My S5 has started to act up. On core 1printing stops and keeps getting message that material is low? I have performed the cleaning process (hot and cold pull). Changed the cores out. The material seems to load into the core, but when I go to print nothing extrudes. I'm using Ultimaker filaments and they are being detected.
Now. no material is being extruded from core 1? The material loads, but when printing a job there is no extrusion?
Ultimaker S5 Pro Bundle w/Print Cores + Filament
in Buying or selling your UltiMaker
Posted
SOLD