[Ultimaker 3 not connecting to correct IP address]

We're having an issue with both our Ultimaker 3's not connecting to the correct IP addresses. Previously we had them set up and pointing to the correct addresses and we could print over the network perfectly however now the IP addresses keep changing on a daily basis on both printers and I am not sure how to get them back to the previous working addresses.

 

Any pointers or advice would be appreciated.

[Does your company use Ultimaker? Know one that does? Let us know!]

Hi Adam,

 

I've sent you a DM regarding an article I have produced for our practice in which we are using UM3's for our Architectural models.

 

Let me know if this is of interest to you.

 

Cheers!

[Do these areas need support?]

2 hours ago, Dim3nsioneer said:

Typically bridges (aka horizontal overhangs between two edges) up to a length of about 7-8mm are fine without support on an Ultimaker printer. If they are longer, special bridging settings could be applied or you (more easily) print it with support.

When you say 'bridging' supports, what do you mean by that and where can I find a setting for it?

[Do these areas need support?]

We're preparing a print and in Cura these windows (and other similar windows around the model) require support material? Is this normal? I know there is essentially an overhang on the lintels but I'm just not sure it needs it?

 

Any suggestions welcome!

[How would we do this?]

We've done the separate route and printed a few at a time, numbered them and placed them on a paper copy that is numbered also. Easiest way to do it currently.

 

Had some issues with grinding but unloading and reloading the material has worked and have successfully printed a few batches today and yesterday which is good!

[How would we do this?]

Yes we did one recently and it looked great! This was before we had our printer though so everything was outsourced. We just had to put it all together at the end!

 

I've started with a batch of houses, once finished we will lay over the glass on the site plan and take off one by one, when it gets to the more complicated areas I think we will be doing them separately!

 

[How would we do this?]

Thank you both for your replies.

 

Yes ideally we want to have everything the same colour, we tend to do our models in white with a wooden laser cut base for the actual site the building sits on.

 

Good to know I can open as many STL's as the plate will fit, might be a case of just placing a whole load of the houses on there, assuming this means I will need to export each house separately from the overall model though?

 

The models will be editable 'I think'. At the moment they are families, but we could add some sort of marker on them maybe. I was looking at the Benchy model we printed and it has the website printed underneath on the bottom layer, I wondered whether this was something of an after addition.

 

[How would we do this?]

Hi guys,

 

We are soon going to be printing a site model for one of our projects, we are outsourcing the base due to size however we have started to model the surrounding buildings. A couple of questions:

 

 

1: Can we print multiple buildings on one build plate to save time?

 

2: Is there a way we can number them on the print so we know where they end up going? (I know this sounds silly!)

 

3: Is this the right way? By that I mean, if anyone has any other better ideas on how to print this I would be all ears, this will be our first full build (other than the actual site!)

 

Thanks guys!

[First Print, couple of questions]

Thank you all for the replies, I didn't know you could block the PVA supports so that is useful, we had support material where I'm not sure we actually needed it so will bear that in mind for future!

 

The combing I will change also, we don't want this happening on future prints at all really!

[First Print, couple of questions]

Hi there, first post!

 

We recently purchased 2 Ultimaker 3's as we are more and more being asked for 3D printed models for our projects. Below are some images from our first 'proper' print and I just have a couple of questions I hope someone may be able to answer:

 

1. there seems to be some small cut-outs in the sides, we're not sure if this has happened when peeling off the PVA or not, if this is the case then in the future we can be more careful when peeling it off. If it's something else, could anyone point me in the right direction as to what the cause might be?

 

2. The lines on the roof, having a look at the other posts it would seem that this is a 'combing' issue, could someone confirm if this is the case? During the print the nozzle was catching going over the infill and fraying the tops a bit so I kind of think it's that, just on the top layer.

 

Other than that, looks like a great bit of kit, the cameras on the printers wouldn't work which is a separate issue I hope to resolve when our next print is running unless there is a way to test the camera without printing anything?

 

Thanks in advance!