Jump to content

furkasocal

Member
  • Posts

    11
  • Joined

  • Last visited

Posts posted by furkasocal

  1. Hello all,

    Lately my CR10s Pro has been starting off each print at a different height. I am using the stock probe on a creality glass bed. I don't adjust the Z offset at all (example I always leave it at -.3) but it seems that sometimes it will print high or way low. To trouble shoot this I stop the print and drop it down say -.3 but it will still be way high or low. There seems to be almost no correlation to the height it starts printing. I of course have tried leveling my bed, lowering the sensor a bit closer to the glass and re adjusting the sensor's sensitivity with the little screw on top. One thing I noticed is that compared to my friend's identical printer his screw seems much more responsive in terms of when the light comes on. I turn the screw just until the light turns on but then it will take 4-5 turns the other way to turn it off. I know these sensors can be affected by all sorts of factors but it seems like this has really gotten worse lately. Do you think maybe my sensor is somehow going bad?

  2. That's a good idea regarding the 45 degrees above the windows. That's totally doable as that inset is for a plexiglas window pane and wouldn't be visible from the outside. I started using supports everywhere because I didn't have alot of success with clean bridging. Do you have any quick suggestions? I have to print in ABS for these parts. 

  3. Hello all,

    I keep having my supports come loose on this big ABS train car I am trying to print. As you can see in the pictures I attached there is a overhang and then the windows which I am using the support for. A few times the support has just fallen out or had terrible adhesion.  I also attached a picture of my settings, I was thinking of reducing everything by half so that the support is closer to the main body of the print? Does anyone else have any suggestions?

    Thanks in advance!

    2CAA8E2E00E6_1587997939499~2.jpg

    IMG_20200427_094408.jpg

    IMG_20200427_094502.jpg

    IMG_20200427_094533.jpg

  4. ;FLAVOR:Marlin
    ;TIME:35273
    ;Filament used: 23.2464m
    ;Layer height: 0.2
    ;MINX:19.2
    ;MINY:89.362
    ;MINZ:0.2
    ;MAXX:280.8
    ;MAXY:210.638
    ;MAXZ:9.6
    ;Generated with Cura_SteamEngine 4.5.0
    M140 S110
    M105
    M190 S110
    M104 S250
    M105
    M109 S250
    M82 ;absolute extrusion mode
    M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
    M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
    M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
    M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
    M220 S100 ;Reset Feedrate
    M221 S100 ;Reset Flowrate

    G28 ;Home
    M420 S1 Z2 ;Enable ABL using saved Mesh and Fade Height

    G92 E0 ;Reset Extruder
    G1 Z2.0 F3000 ;Move Z Axis up
    G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
    G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
    G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
    G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
    G92 E0 ;Reset Extruder
    G1 Z2.0 F3000 ;Move Z Axis up

    G92 E0
    G92 E0
    G1 F2700 E-5
    ;LAYER_COUNT:48
    ;LAYER:0
    M107
    G0 F6000 X24.969 Y89.664 Z0.2
    ;TYPE:SKIRT
    G1 F2700 E0
    G1 F1200 X25.738 Y89.485 E0.02626
    G1 X26.522 Y89.385 E0.05255
    G1 X27.117 Y89.362 E0.07235
    G1 X34.2 Y89.362 E0.30793

  5. I am new to 3d printing so I apologize in advance if this is a basic question. But every time I start a print during the initial purging of the nozzle, my CR 10s Pro draws this triangle on the bed, I would prefer it to just draw a line down the side so that it doesn't interfere with the Initial layer of the actual print. Does anyone know how to adjust this? I'm using Cura 4.5 as my slicer. 

    traingle.jpg

×
×
  • Create New...