Jump to content

SidGates

Dormant
  • Posts

    6
  • Joined

  • Last visited

SidGates's Achievements

0

Reputation

  1. I will your suggestions tomorrow. It is now printing in the center of the build plate. Thanks Sid
  2. I just sliced again and I don't know much about G-code but I think this one may be right. The "x" values seem better to me. ;Generated with Cura_SteamEngine 4.6.1 M140 S60 M105 M190 S60 M104 S210 M105 M109 S210 M82 ;absolute extrusion mode ; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish G92 E0 G92 E0 G1 F1500 E-6.5 ;LAYER_COUNT:31 ;LAYER:0 M107 G0 F6000 X107.294 Y55.514 Z0.2 ;TYPE:SKIRT G1 F1500 E0 G1 F1200 X108.196 Y55.567 E0.03005 G1 X109.089 Y55.699 E0.06008 G1 X109.967 Y55.91 E0.09011 G1 X110.823 Y56.198 E0.12015 G1 X111.65 Y56.56 E0.15018 G1 X112.442 Y56.995 E0.18023 G1 X113.193 Y57.497 E0.21027 G1 X113.896 Y58.064 E0.24031 G1 X114.546 Y58.691 E0.27035 G1 X115.138 Y59.373 E0.30039 G1 X115.668 Y60.104 E0.33042 G1 X116.13 Y60.88 E0.36046 G1 X116.523 Y61.693 E0.39049 G1 X116.841 Y62.538 E0.42052 G1 X117.084 Y63.408 E0.45056 G1 X117.249 Y64.296 E0.4806
  3. You are right it is checked. I changed it when I first had the trouble yesterday and thought I had unchecked it. Below is unchecked version and photo of my printer setting. You said to use 235 but mine has always been at 200. After uncheck. ;FLAVOR:Marlin ;TIME:1585 ;Filament used: 1.02285m ;Layer height: 0.2 ;MINX:81.843 ;MINY:54.703 ;MINZ:0.2 ;MAXX:118.157 ;MAXY:145.297 ;MAXZ:6.2 ;Generated with Cura_SteamEngine 4.6.1 M140 S60 M105 M190 S60 M104 S210 M105 M109 S210 M82 ;absolute extrusion mode ; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish G92 E0 G92 E0 G1 F1500 E-6.5 ;LAYER_COUNT:31 ;LAYER:0 M107 G0 F6000 X107.294 Y55.514 Z0.2 ;TYPE:SKIRT G1 F1500 E0 G1 F1200 X108.196 Y55.567 E0.03005 G1 X109.089 Y55.699 E0.06008 G1 X109.967 Y55.91 E0.09011 G1 X110.823 Y56.198 E0.12015
  4. Greg- I set Cura 4.6.1 to the parameters you suggested and below is the result. I will try to run this on my machine in a few minutes. Sid ============================== M105 M190 S60 M104 S210 M105 M109 S210 M82 ;absolute extrusion mode ; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish G92 E0 G92 E0 G1 F1500 E-6.5 ;LAYER_COUNT:31 ;LAYER:0 M107 G0 F6000 X7.294 Y-44.486 Z0.2 ;TYPE:SKIRT G1 F1500 E0 G1 F1200 X8.196 Y-44.433 E0.03005 G1 X9.089 Y-44.301 E0.06008 G1 X9.967 Y-44.09 E0.09011 G1 X10.823 Y-43.802 E0.12015 G1 X11.65 Y-43.44 E0.15018 G1 X12.442 Y-43.005 E0.18023 G1 X13.193 Y-42.503 E0.21027 G1 X13.896 Y-41.936 E0.24031 G1 X14.546 Y-41.309 E0.27035
  5. Greg, thanks for the reply. I will try your suggestion this morning. My description wasn't adequate. Last night I remembered I also have Prusa slicer on my computer so I sliced the same object wih it and the printing location was normal in the center of the bed. I also reloaded Cura 4.4.o and now have the same problem when slicing with 4.6. When using 4.6 the printer lays down a strip of filament very near the left edge of the bed and then comes back to the left front corner and start printing my object. The Z position appears to be normal but the object is partially printed on the corner of the bed and partly in the air to the left of the bed. Start of my g-code file ;FLAVOR:Marlin ;TIME:2209 ;Filament used: 1.35208m ;Layer height: 0.2 ;MINX:-7.739 ;MINY:-34.097 ;MINZ:0.2 ;MAXX:7.739 ;MAXY:34.097 ;MAXZ:6.2 ;Generated with Cura_SteamEngine 4.4.0 M140 S60 M105 M190 S60 M104 S200 M105 M109 S200 M82 ;absolute extrusion mode M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk M220 S100 ;Reset Feedrate M221 S100 ;Reset Flowrate G28 ;Home G92 E0 ;Reset Extruder G1 Z2.0 F3000 ;Move Z Axis up G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line G92 E0 ;Reset Extruder G1 Z2.0 F3000 ;Move Z Axis up G92 E0 G92 E0 G1 F1500 E-6.5 ;LAYER_COUNT:31 ;LAYER:0 M107 ;MESH:TX Tray Latch v1.stl G0 F6000 X-5.763 Y4.303 Z0.2 ;TYPE:WALL-INNER G1 F1500 E0 G1 F1200 X5.761 Y4.303 E0.38329 G1 X5.763 Y4.303 E0.38336 G1 X5.763 Y0.892 E0.49681 G1 X5.763 Y-4.303 E0.66959 G1 X-5.761 Y-4.303 E1.05288 G1 X-5.763 Y-4.303 E1.05295 G1 X-5.763 Y4.303 E1.33919 G0 F6000 X-5.363 Y3.903 G1 F1200 X5.363 Y3.903 E1.69593 G1 X5.363 Y-3.903 E1.95556 G1 X-5.363 Y-3.903 E2.31231 G1 X-5.363 Y3.903 E2.57194 G0 F6000 X-4.963 Y3.503 I sent the whole file to a friend who has the same p;rinter and is using 4.6 and I will hear from him this morning. CE3_TX Tray Latch v1.gcode
  6. I have been using Cura 4.4.0 since Dec. on my Ender 3 with no problem.. I upgraded to 4.4.6 and now my prints are off the table in the left front corner. Stumped.
×
×
  • Create New...