UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
Most of these are pretty obvious, but based on the RepRap gcode lookup I can't figure out M118 or M651
M118 is a good question, but M651 turns ON the chassis fan, where M652 turns it OFF.
On 12/23/2020 at 3:53 AM, apaier said:
Anyone have any tips or pointers for next steps? I'd love to get Cura working with the Creator Max.
I have my Adventurer 3 working with Cura using the following G-Code, might work with your Creator with few tweaks. I export the regular .gcode file and simply rename to .g and it works fine loading into FlashPrint and sending to print (I do this as its faster and easier then through an USB drive).
Start G-code
Code
Explanation
M651
G90
G28
M132 X Y Z A B
G1 Z50 F3300
M7 T0
M6 T0
M907 X100 Y100 Z40 A100 B20
Turns the chassis fan ON
Sets the printer to absolute positioning
Moves to home position
Loads the axis offset of the current home position
Moves 50mm on Z axis and sets feed rate to 3300 mm/s
Mist coolant ON
Tool change
Set digital trimpot motor current
End G-code
Code
Explanation
M652
M107
M104 S0 T0
M140 S0 T0
G91
G1 F150
G1 Z10
G90
G28
G1 X0 Y0 F1200
M84
Turns the chassis fan OFF
Turns the extruder fan OFF
Sets the extruder 0 temperature to 0 degrees
Sets the bed 0 temperature to 0 degrees
Sets the printer to relative positioning
Sets the feed rate to 150mm/s
Raises the Z axis by 10mm
Sets the printer to absolute positioning
Moves to home position
Moves to coordinates 0,0 and feed rate to 1200 mm/s
Can Cura be used to Generate the .g or .gx file?
in UltiMaker Cura
Posted
M118 is a good question, but M651 turns ON the chassis fan, where M652 turns it OFF.
I have my Adventurer 3 working with Cura using the following G-Code, might work with your Creator with few tweaks. I export the regular .gcode file and simply rename to .g and it works fine loading into FlashPrint and sending to print (I do this as its faster and easier then through an USB drive).
Start G-code
Code
Explanation
M651
G90
G28
M132 X Y Z A B
G1 Z50 F3300
M7 T0
M6 T0
M907 X100 Y100 Z40 A100 B20
Turns the chassis fan ON
Sets the printer to absolute positioning
Moves to home position
Loads the axis offset of the current home position
Moves 50mm on Z axis and sets feed rate to 3300 mm/s
Mist coolant ON
Tool change
Set digital trimpot motor current
End G-code
Code
Explanation
M652
M107
M104 S0 T0
M140 S0 T0
G91
G1 F150
G1 Z10
G90
G28
G1 X0 Y0 F1200
M84
Turns the chassis fan OFF
Turns the extruder fan OFF
Sets the extruder 0 temperature to 0 degrees
Sets the bed 0 temperature to 0 degrees
Sets the printer to relative positioning
Sets the feed rate to 150mm/s
Raises the Z axis by 10mm
Sets the printer to absolute positioning
Moves to home position
Moves to coordinates 0,0 and feed rate to 1200 mm/s
Stops the idle holds on all axis and extruder