Hello,
Forgive me if this is the incorrect place for this topic—new to these forums.
I was 8.5 hours into a 9-hour print when a snag in the filament spool caused the print to "finish" the last 30 minutes with no actual extrusion happening. I've identified the Z-Height where the failure happened, and want to continue the print from that point by removing all GCode before that point. In looking at the Cura GCode, I'm realizing that rather than being noted in a really obvious place (such as as the beginning of a new layer), the Z-Height is listed in what seems like the tail-end of a layer among a lot of other code that I'm having trouble deciphering. Basically, I want to remove all code from before my relevant point, but afraid of deleting something important (like extrusion info). Can somebody lend a hand in where I should be editing the code from? I also understand that I'll need to modify some of the startup code, so I won't just be deleting everything before this point.
The Z-Height I need to be at is 119.6. I've made the Z-Height line bold, as well as the start of the next layer in this cut/paste of the section below.
Thanks for reading!
---
G1 X71.679 Y132.971 E179.90897
G1 X71.709 Y132.527 E179.92377
G1 X71.807 Y132.043 E179.9402
G1 X71.981 Y131.528 E179.95828
G1 X72.229 Y131.025 E179.97693
G1 X72.498 Y130.605 E179.99352
G1 X72.812 Y130.215 E180.01017
G1 X73.2 Y129.826 E180.02845
G1 X73.61 Y129.49 E180.04608
G1 X74.047 Y129.201 E180.0635
G1 X74.512 Y128.964 E180.08086
G1 X75.005 Y128.781 E180.09835
G1 X75.491 Y128.662 E180.11499
G1 X76.023 Y128.589 E180.13286
G1 X76.544 Y128.573 E180.15019
G1 X77.012 Y128.607 E180.1658
G1 X77.54 Y128.707 E180.18367
M204 S3000
M205 X10 Y10
G0 F6000 X77.729 Y128.77
G0 X77.476 Y129.528
G1 F2400 E174.18367
;MESH:NONMESH
G0 F600 X77.476 Y129.528 Z119.6
G0 F6000 X78.31 Y129.507
G0 X79.057 Y128.465
G0 X69.85 Y111.899
G0 X69.377 Y110.67
G0 X69.083 Y109.509
G0 X68.926 Y108.155
G0 X69.017 Y106.293
G0 X69.412 Y104.54
G0 X70.067 Y102.831
G0 X71.173 Y100.787
G0 X73.074 Y98.036
G0 X82.587 Y86.112
G0 X84.882 Y83.522
G0 X86.653 Y81.854
G0 X88.192 Y80.7
G0 X89.954 Y79.716
G0 X91.156 Y79.239
G0 X92.601 Y78.858
G0 X94.467 Y78.667
G0 X114.111 Y79.673
G0 X115.244 Y79.07
G0 X115.963 Y76.581
;TIME_ELAPSED:28935.329936
;LAYER:597
M204 S1800
M205 X8 Y8
;TYPE:FILL
;MESH:Centoculops_Posed_3DPrint.stl
G1 F2400 E180.18367
G1 F3000 X118.565 Y73.979 E180.30606
G1 X118.591 Y73.973 E180.30695
G1 X118.962 Y73.93 E180.31937
G1 X119.366 Y73.942 E180.33281
G1 X119.682 Y73.997 E180.34348
G1 X119.998 Y74.092 E180.35446
G1 X120.246 Y74.196 E180.3634
G1 X120.465 Y74.323 E180.37182
G1 X120.476 Y74.331 E180.37227
G1 X116.042 Y78.765 E180.58084
G1 X116.157 Y78.971 E180.58868
G1 X116.297 Y79.159 E180.59648
G1 X116.488 Y79.353 E180.60553
G1 X116.691 Y79.514 E180.61415
G1 X116.993 Y79.7 E180.62595
G1 X117.2 Y79.794 E180.63351
G1 X117.258 Y79.811 E180.63552
G1 X121.324 Y75.745 E180.82677
M204 S3000
M205 X10 Y10
---