-
Posts
35 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Events
3D Prints
Everything posted by Pena
-
Hey Cyriaquer, I took your advice and removed the Radial fans, see attached photos. The fans were horribly dirty which I think altered the fan blades by placing them out of tolerance or out of balance. I used my shop air compressor to carefully blow the blades and being careful not to over clock or exceed RPM rating and break the blades. I then used a brush to rub off stuck on dust and gave them a final compressed air cleaning. I did this to the fan support housing as well. I put everything back together and voila the printer is working. I've completed two prints back to back with no issues. I also ordered two knew radial fans (Print core side fans) or Model Cooling Fan Part #UM3/UM3X/S5/S3/S7 for my S5. and will replace the old fans if I have anymore leveling issues. Thank you for your awesome advise and support! Dan
-
Hey Guys Now with everyones help, I understand the noise level results of the Level Sensor Test shouldn't exceed 8.0 Your help is much appreciated! Dan
-
Thanks Guys! With all the information everyone has provided, I've narrowed it down to the capacitive sensor board. I found a Fan wire crossing directly over the PCB, the fan wire was being squeezed between the heating element wires of the print core and the PCB. I moved the fan wire, ran the test Level Sensor Test aging with the following results. Again thanks! Dan
-
Hey Guys, I've had an issue off and on in regards to leveling results on my S5. I thought my leveling error had something to do with the magnets I installed on my build plate however, the error is repeated with a glass build plate and no magnets. I have replaced both AA and BB nozzles with new nozzles and cleaned the nozzle seating areas. I have completed the manual level procedure and leveling sensor test several time. When I reboot the S5 and repeat the manual leveling the error returns. Once I remove the New Print Head Nozzle and reinstall the same new nozzle the S5 will randomly level and start working. My question is: how is the information received from the Leveling Sensor Test used or how can it be helpful? Dan
-
Ultimaker S5 Build plate Auto Leveling issue
Pena replied to SparkytheProto's topic in UltiMaker 3D printers
Hi Viktor, I was wondering if disabling the auto leveling feature on your S5 is working or has it caused other issues? My S5 is having the same issue. Thanks Dan -
I received the following for a toy I created using my Ultimaker S5! Congratulations! You and your product, FireFly (Kinetic Energy Toy), have been selected to be showcased at Toy Fair’s Creative Factor Inventor Day! I will reveal the design during the event, Tuesday, October 3 at the Javits Center in NYC from 10 AM – 1PM,! Thank you UltiMaker! Dan
- 1 reply
-
- 1
-
Does anyone know of a return option to the previous task in the printing cycle for the S5? You know, the task that was going fantastic just before it went dumfounded and didn't print anything!
-
You might also research Quality - Layer Height in Cura material settings.
-
-
Have you tried reducing your print seed and keeping your TPU filament dry?
- 6 replies
-
- UMS5
- Essentials user
-
(and 1 more)
Tagged with:
-
It looks like your print is sheering apart, have you tried slowing the print speed and keeping the filament dry?
-
Verify your filament is kept dry, you can weigh the material after opening the material for the first time. Also when not in use I store 4 rolls of TPU material in 2 lbs. silica gel beads.
-
Printer error persists in Digital Factory but prints fine
Pena replied to glx's topic in UltiMaker Digital Factory
I get this issue when printing translucent materials, I disabled the flow sensor in the printer settings. -
The printer is showing up however the Camera function isn't available. The only access to the printer's camera is by way of using DF.
-
I firmly press and drag two fingers on my Mac track pad, this allows me to rotate the bed. I lightly press two fingers and drag to zoom. I hope this helps.
-
Hey Guys, So I followed each line item as instructed per error ER31, nothing worked "very frustrating"! I decided to remove the heating element from BB nozzle 2 and replaced just the heating element from an extra print core AA. All is working perfectly! I've been looking for a replacement heating element for my BB print nozzle 2. My preference is to purchase only the heating element. Does anyone know if I am limited to purchasing the entire BB print core/nozzle? Is it possible to purchase just the BB heating element, if so where and is there a part number?
-
Hey guys, Is anyone having issues with the Cura software connecting to the Ultimaker S5 printer? I see my printer is available on the digital factory in standby, but Cura won't locate it. I have the S5 attached using my Ethernet and it provides an IP address. So I tried adding it using the IP and it will snap a quick glimpse of the S5 then disappear. I was finally able to get it all connected after several reboots.
-
Looking for U.S. supplier for the Ultimaker S5 fan
Pena replied to Pena's topic in UltiMaker 3D printers
Customer service responded immediately and I am pleased! Thank you! -
Looking for U.S. supplier for the Ultimaker S5 fan
Pena replied to Pena's topic in UltiMaker 3D printers
I’ve sent a request to customer service to help send both of my orders in one order. -
Looking for U.S. supplier for the Ultimaker S5 fan
Pena replied to Pena's topic in UltiMaker 3D printers
Thank you, I’ve placed my order! you’re awesome! -
Looking for U.S. supplier for the Ultimaker S5 fan
Pena replied to Pena's topic in UltiMaker 3D printers
Thank You! -
Looking for U.S. supplier for the Ultimaker S5 fan
Pena replied to Pena's topic in UltiMaker 3D printers
Thank You but Digikey is out of stock -
Has anyone found a U.S. supplier for the Ultimaker S5 fan, I need a replacement? SUNON MC35100V2-000U-A99 M Series 35 x 35 x 10 mm 5 V 6.5 CFM 0.38W