Jump to content

koreandi1

Dormant
  • Posts

    8
  • Joined

  • Last visited

Everything posted by koreandi1

  1. Dankeschön. Habe gerade erfahren, dass ich mich bei der Firmware an der U2 und nicht U2+ Firmware bedient habe. 🙂 Deshalb war mein Extruder anfangs verkehrt und meine Steps stimmen nicht. Werde das nochmal neu compilen (https://github.com/Ultimaker/UM2.1-Firmware).
  2. You are a genius.. Yes, my extruder was reversed. I swapped one coil and that was done. Alle setting where factory-reset. Yes, but that didn´t bother me, because I never worked before with this printer. I will take the time and recompile it with the linked Firmware. So the difference between the way I compiled and the linked topic is that I wouldn't loose all printer settings?
  3. Hi all So my board has a functional E1 port. If I talked about E1 it should be called E1. The first extruder is E1 and the second is E2. I am used to other boards that names the first extruder E0. I changed the Pins in the FW and it works really fine. I just have to adjust my E-Steps. I changed the slicer to 125% to fix that temporarily. But I have to admit that I complied the Firmware without going through all that processes that was replied first. I disconnected the board to investigate the problem. Then I powered it up, plugged in USB, used Arduino 1.8.13 to change and compile "Ultimaker2Marlin-master" sketch. It was done in 5 minutes. greetings
  4. Guten Morgen "zerspaner_ger", es hat alles einwandfrei funktioniert. Der UM läuft. lediglich meine E-Steps müsste ich korrigieren. Muss den Durchfluss auf 125% stellen. Hab das per Slicer korrigiert, werde das aber noch in der FW fixen. Danke
  5. So, thank you, I will start to go through the process... My Board is: Ultimainboard rev. 2.1.4 In Pin.h there is a section with pin-assignement: * Ultiboard v2.0 pin assignment #define E0_STEP_PIN 49 #define E0_DIR_PIN 47 #define E0_ENABLE_PIN 48 #define E1_STEP_PIN 49 #define E1_DIR_PIN 47 #define E1_ENABLE_PIN 48 So those are the values I have to change / swap? Thanks.
  6. Ja, der zweite Schaltkreis ist vorhanden. Habe das auch gelesen, dass die Chipsets am E1 fehlen. Ich werde es bevorzugt mal mit dem Ändern der Firmware probieren. In meinem anderen Post wurde darauf verlinkt: Plan B ist dann wirklich DUET Wifi zu erbauen. Hab das an meinem Kodak Drucker auch schon gemacht und ging wirklich einfach. Ist halt der finanzielle Aspekt... 🙂 Gruß
  7. Hallo zusammen, ich hab den Post auch bereits in dem Firmware-Channel gepostet... Ich habe einen defekten U2+ zu einem sehr guten Preis mit viel Material bekommen. Das Board ist defekt, bzw. der E0 Kreislauf. X / Y / Z funktionieren und können am Drucker bewegt werden (Homing). Der E1 Schaltkreis schaut unbeschädigt aus. Kann man den E0 an den E1 Ausgang hängen und die Firmware entsprechend ummappen? Mein alternativer Plan wäre sonst ein Smoothieboard (vorhanden) zu nehmen oder auf ein DUET Wifi umzusteigen. Vielleicht hat ja von euch jemand einen Tipp oder bereits Erfahrung damit. Danke und Grüße
  8. Dear community, I just got a damaged Ultimaker 2+ for a very good price. The Mainboard blown up on start up since then E0 is not working anymore. After dissassmbing the mainboard there are some blownup capacitors and diodes on the E0 circuit. X / Y / Z are working fine. Can I connect the E0 Extruder to the E1 Output an map the firmware? E1 looks just fine. Alternative my plan is to use a Smoothiware or DUET Wifi board. Thanks and have a nice weekend.
×
×
  • Create New...