Jump to content

LordHokage

Member
 View Profile  See their activity

  • Posts

    35

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by LordHokage

  1. LordHokage
    hmmmmm I've never had this problem before. Also, I've just removed the heaters for my Hotend and tried it again and it did the same thing. Would posting my configuration.h and configuration_adv.h help?? Thanks though for replying @ahoeben
  2. LordHokage
    Hi Everyone, I've got an Ultimaker Original Plus here and I've just updated it to Marlin 2.1.x. However, when I reach the nominal bed temperature, it restarts. Does anyone know why this happens? Is it a hardware or software issue here? For reference, it worked fine with the older firmware. Kind Regards!
  3. LordHokage
    Hi everyone! I've got a UMO+ and wanted to get some timely upgrades for it. I got reading through some history and found some upgrades, all of which have been doing me well.... One of my final ones is this one: YouMagine – Symmetric Dual Fans UMO/UMO+ 30mm / 40mm / 50mm by Neotko / Sugarpop! – YouMagine 🔧 In the description of that one, it does give a link to some instructions. I click on the link to find that it gives an error. Can anyone fill me in on what's happened and more pressingly, put in the a) working link or b) instructions c) give me their instruction as to how I'm supposed to do it. broken link: https://ultimaker.com/en/resources/20503-ultimaker-original-dual-fans-upgrade Kind Regards and thank you!
  4. LordHokage
    @Smithy (and @Mechatron127) thank you. I will try that this weekend. I was thinking about the line widths.. As this is a printer for work, it would be ideal to find the original c-clip. Where can I get one? I rather not print them if I can do so
  5. LordHokage
    Interesting thought there @Smithy!! I really do think it is just me not levelling the bed properly. Do you have any clip models you think work well?? I will try relevelling the bed again but the nozzle diameter is 0.4. It that a problem??
  6. LordHokage
    @Mechatron127, I bought this printer second hand so I don't actually know the line diameter....I'd assume that it would be the standard UMO+ nozzle. @Smithy, I've gone through this a million times, but how much scratch?? Also, the bowden clips have both disappeared, where would I get replacements instead of printing shoddy ones.
  7. LordHokage
    ok @Smithy here they are. Please ignore the blob on the first picture, that was when i stopped the print. It's either gaps in the extrusion lines or just no extrusion at all with this guy.
  8. LordHokage
    @Smithy, I got one slightly better print but even jacking up the flow rate did nothing... I think it has to do with my bed levelling. That's always the problem right?
  9. LordHokage
    @rowiac, @amedee, I do intend to change the GT2 belts, just didn't know where to start. But my question on the extruder still stands because it has been giving me lots of headaches since forever ;(. But would the ZGE still work without the UM2 printhead and directly on the UMO+ printhead
  10. LordHokage
    IDK Man. 4 years later, i'm still wondering...
  11. LordHokage
    This is kinda old. But I still have a UMO+ with everything stock. Would this still work?? Additionally, are there any mods for the terrible UMO extruder?
  12. LordHokage
    @Smithy Everything seems ok. Retighten the pulley's? There doesn't seem to be any layer shifting though.. I thought about the calibration card because I don't trust my manual bed levelling...
  13. LordHokage
    @Smithy and @GregValiant, do you guys think its got anything to do with the position of the z-stop?? It is a umo+ after all..
  14. LordHokage
    This is the top layer (sorry for not clarifying in my post) with ironing. I thought that ironing the top might help but it didn't. I don't have a calibration card, and there are none in Australia, where do you think I could get some? It was left and I bought it after a while but I keep printing every week on the weekends so I'd like to think that its exercised. I'll retry tightening the pulleys but do you think its got something to do with the e-steps??
  15. LordHokage
    Hi everyone! I hope you doing well and staying safe. I turned on my UMO+ after a while and started to print. I seem to get these gaps and have tried to fiddle with settings and bed levelling to get it to work to no avail. I've attached two pictures below that should give some idea of what's happening. Any suggestions? Thanks!
  16. LordHokage
    I found this out from Scott Yu-Jan, Water works really well. Carefully spray some or pour a few ml's near the print surface and give it some time. Due to capillary forces, the water goes under the print and it unsticks. Ley me know how it goes for you 😉
  17. LordHokage
    I guess I'm resurrecting a "dead" thread. I was going around and was wondering how I was going to make auto levelling on the UMO+ work. There wasn't any definitive guide on doing so. Does anyone have and resources or steps as to make the BLTouch work with the UMO?
  18. LordHokage
    Thank you @amedee! Regarding your response, I still have some questions. What type of oil do you use and where? Do you just let it run through the "hole where the filament goes"?(I actually don't know its name ;). Does that mean that there is a native 24V point on the extruder for me to plug it in? * Another couple questions: What are the best blocks (the black part the gantry sits on)? Any resources to use the BL-Touch with the UMO+? and What UMO+ firmware changes to make bed levelling work on pin 13 like "Automatic bed leveling for Ultimaker Original | F1OAT CNC experiments"? Does anyone else like @f1oat or @vanalleswat have any suggestions for the bed levelling?
  19. LordHokage
    Hi everyone! I have several questions about the E3D upgrade for my UMO+! I'll list them below so people can answer them directly: Can I use a 12v version? If not, why? If I upgrade the extruder (to 1.7mm), can I get the 1.7mm version? If I use the original heating parts from the UMO+ and add that to the E3D, will I bypass the MOSFET changing? What other methods can I use to change from 2.85mm to 1.75mm? Is the E3D good for PLA/ABS? What is the deal with the Olsson Ruby Nozzle? Sorry if that was a lot of questions, I just needed to clarify everything before I buy the E3D for my UMO+. I hope that @neotko and @amedee have some suggestions... Thanks for your time and response!
  20. LordHokage
    I'm super late here but I'll just ask a question. Can I use the 12v version of the E3D v6 instead of the 24v version? Thanks!
  21. LordHokage
    What are my options of using E3D v6 with the UMO+...
  22. LordHokage
    I am in Sunny Australia. Why?
  23. LordHokage
    Hi everyone! Does anyone have any guides/resources on how I'd go about retrofitting (where do I even buy them) UM2 kits for my UMO+? Thanks in advance!
  24. LordHokage
    Hi there! The Fan is disabled (currently) but the picture attached is the best one I can provide at the moment.
  25. LordHokage
    Hi everyone, I have been doing some hours on my UMO+ recently (I know it's old) but have had print stop at the initial layers because of filament messes such as the one attached. I have disabled retraction but the problem still persists. @neotko or anyone else, would you have any suggestions to the prevention of this problem?
×
×
  • Create New...