D1ggie

I tried the gcode. The printer goes to the middle of the build plate and stays there. And after about a minute it ends the program.

Hello again. I'm back. Sorry for not replying sooner. Printer has been very busy these days. 😅 But the problem persists and I'm getting frustrated of what can be the problem. I only want to replace the board in last resource and after figuring that it's really the problem. Did you come with another possible solution? Thanks.

Yes, I have that box to choose if I want with M109 or M104. I left it enabled. I don't know why but I saw the extruder comming backwards a bit. But let me try the program again.

Still doesn't work dude. And even tho I put 0 on the retract box it stills retract a bit when I resume. But it's still not printing at the right hight. I put the 3mf file asweel so you can have a look. CE3_20mm_cube.3mf

Hello again. So I tried changing only the retraction when it pauses. I used always the same filament and even testes pull it back a bit just like you said but still not working. I always wait about 10 minutes afeter it pauses to kinda "simulate" a normal change filament. How can I send a video showing what happens?

ok, I'll try that way. After testing that let's see how the print comes out xD

No problem. Hope you are ok. When you find time to look at it just repply here.

Done. Here you go CE3_20mm_cube.3mf

It is better, much better actually. Now what is bothering the most is that the printer retracts right before reaching the part. I even tried to push the clamp on the extruder when it retracts but somehow it anyway and starts to print extruding material but since it is too far from the hot end It takes time to start comming out. But the piece is much better.

Yes, I resume dthe print with no problem. It noly makes a retraction and pushes the filamento too far back but that's something on the slicer (need to fin what it is xD). There's no way to always keep the stepper on? Whithout a timeout? For example, if It pauses and I'm not at home and take more than 30minutes to come back it will lose position anyway. I'll try to do as you say but can I keep the steppers always on? Whithout any timeout?

It's a simple 20x20x20 cube with no top, infill or bottom. CE3_20mm_cube.gcode

It didn't work... It still starts above of what is suppose to...

Hello everyone. So the issue is: Sometimes my computer crashes and goes into bluescreen and restarts by himself. And it's not he first time that happens and I have the cura software opened. The issues is that if I try to open it again it does not open. The cura software with version that was opened when it crashed don't open anymore, the only way for me to use cura is use the version 5.0.0 (I can't open the version 5.1.1) I already tried restarting the computer, uninstall and install again that version and it still doesn't work. Does anyone know how to fix this?

The computer crashes and than goes do bluescreen but it restarts by himself. I already tried restarting the computer, uninstall the cura and intall it again and nothing works... The thing is that I still have the cura 5.0.0 and the version 5.1.1 that I had opened don't work but the 5.0.0 opens no problem. And untill now the only way I can open cura is when comes a new update I istall it and works perfectly fine... The only way for me to use cura is by using the 5.0.0 version. Thanks anyway. I'll try your workaround on that version to see if it works.

I won't be able to test it for now... maybe you know the aswer to this issue aswell. Sometimes my PC crashes into blue screen and restarts. The thing is that if I have cura opened when it does I can't open it again unless is another version that didn't happened the crash. Have you ever heard of something like that? I know it's off topic but I can't test the workaround unless I have cura back. xD