Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Posted (edited) · Merlin Jerk Speed

I'm going through the Merlin code to get a complete understanding of its control over the steppers.

I believe JERK is defined as the instantaneous allowed change in velocity (mm/sec) that can ignored at a junction so that the speed does not have to go all the way to zero.

Merlin has the default XY jerk defined as 20mm/sec.

Merlin has the default XY acceleration defined as 4000 mm/sec2.

Kinematics states that v(i) = sqrt(((v(i-1) * (v(i-1)) + (2 * Acc))

If we want to see the delta change in speed (v) we can choose v(i-1) to be 0 therefore

DeltaV = sqrt(2 * Acc);

Placing the Merlin values in .... DeltaV = sqrt(2 * 4000) = 89 mm/sec which is about 4.5 times the default Jerk value.

My question is .... if Jerk is defined as the maximum change in speed that can occur at a junction and be ignored --- then should it not also be the maximum change in speed allowed during acceleration or deceleration?

If at a junction you don't want more than an change in Jerk speed (20mm/sec) then why should acceleration be allowed to produce a change of speed of 89mm/sec and be acceptable?

Thanks

Edited by Guest
  • Like 1
Link to post
Share on other sites
Posted · Merlin Jerk Speed

Reprint from Merlin code:

// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)

#define DEFAULT_XYJERK 20.0 // (mm/sec)

#define DEFAULT_ZJERK 0.4 // (mm/sec)

#define DEFAULT_EJERK 5.0 // (mm/sec)

  • Link to post
    Share on other sites
    Posted (edited) · Merlin Jerk Speed

    I always thought that jerk was the acceleration of the acceleration.

     

    Interesting math either way...

    I found this (fairly old) discussion on the RepRap forum.

    As far as i understand, "jerk" is the derivation of acceleration (mathematically)...

    ...but... ... in Marlin it is not implemented this way (strictly speaking).

    I may be wrong, but i think it's simply the maximum change of speed at which Marlin joins two segments in the planner.

    Edit:

    You should also take a look at this thread - with a detailed explanation from @gr5.

    Edited by Guest
  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
        • 4 replies
    ×
    ×
    • Create New...