Jump to content
Ultimaker Community of 3D Printing Experts

Ultimaker Original - temperature drops of 30°C!


Recommended Posts

Posted · Ultimaker Original - temperature drops of 30°C!

Hello everybody. I have problems with my Ultimaker Original. It started 3 months ago. Temperature readings were inaccurate as it was too cold or too hot. PLA strated making bubbles. Ok, I though I need new temp sensor. Oredered 2 of them to prevent off times in future.

So I replaced temperature sensor and started test print. Heated up to 220/220°C, but as soon as it started homing, the temperature drop to 190°C and printer continued with heating to 220°C. It reached 220°C again, but real temperature was in that moment about 250°C.

I thought it was a bad temperature amplifier. So I changed the amplifier board. Same story. Reached print temperature of the test print, but as soon as it was homing (reaching 0;0;0), temp dropped to 189°C...

Is there anybody with similar issue? Or does somebody have clue what is wrong? Thanks for every hint and tip!

  • Link to post
    Share on other sites
    Posted · Ultimaker Original - temperature drops of 30°C!

    I would check if there is not a half loose wire in the temperature sensor or to the connection to the board. If I am not mistaken if it can not read the amplifier it keeps the old value. Since you say when homing it changes that makes me think it is a half loose connection.

    Not very scientific advise...

    Wiggle a bit with the cables to see if the temperature readout remains the same.

  • Link to post
    Share on other sites
    Posted · Ultimaker Original - temperature drops of 30°C!

    I recently upgraded my UMO to the Heated Bed Plate and while I had everything apart, I discovered a lot of things had come loose over the years.

    Some of the electronic terminals needed a half twist to be snug again.

    I also had the two back cover pieces to the rods come apart...the nut was still on the thread but it wasn't a lot of fun to put back together!

    Good luck!

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 16 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...