Jump to content
Ultimaker Community of 3D Printing Experts

How can I slow down the Layer:2 WALL-INNER Feedrate


stonethrow
 Share

Recommended Posts

Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

The first layer of print is beautiful with an extrusion G-code feedrate of F600. Then for subsequent layers the feedrate jumps up to F1300 and extrudes too much material making all of the rest of the layers bumpy and overlapped.

Can anyone tell me what Cura config value I must change to decrease the extruder feed for subsequent layers?

;LAYER:2

;TYPE:WALL-INNER

G1 X-9.35 Y-9.35 Z0.6 F1733.3333

G1 X9.35 Y-9.35 F1300.0 E0.8789

Thanks,

  • Link to post
    Share on other sites

    Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

    Your feed rate should be a byproduct of the speed you are printing. The E value should be the determinant on the amount of material fed. If you have already done the Cura first step wizard to get an approximate value of steps/e then you probably need to adjust filament size. You could get that feed rate back to 600, though, by matching your print speed with your first layer speed.

  • Link to post
    Share on other sites

    Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

    Feedrate has nothing to do with the amount of material extruded. Feedrate is actually movement speed (the name comes from CNC milling, where feedrate is how fast you feed it new material to cut)

    The E values control how much material is pushed down the nozzle. Combined with the M92 Exxx which sets the amount of stepper motor steps needed for 1mm of material extrusion.

  • Link to post
    Share on other sites

    Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

    Our extruder motor is spinning too fast. Changing the printing speed doesn't seem to affect the extrusion speed that much. Can you tell me what the printing speed setting actually controls?

    Should we be setting the travel speed down instead?

    Thanks

  • Link to post
    Share on other sites

    Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

    We're actually using our own geared motor on a different system but using Cura for the slicing.

    Is it the packing density setting that changes the extruder feed rate in the G-code? It seems that increasing the packing density setting decreases the extrusion feedrate. Is this right?

    Thanks

  • Link to post
    Share on other sites

    Posted · How can I slow down the Layer:2 WALL-INNER Feedrate

    Yes. The packing density reversely effects the extrusion amount.

    But what you want to adjust, is the "steps per E", you need to tel the firmware how many stepper steps you need for 1mm of extrusion.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
        • 11 replies
    ×
    ×
    • Create New...