Jump to content
Ultimaker Community of 3D Printing Experts

Laser attachment for engraving - Ultimaker 2


Recommended Posts

Posted · Laser attachment for engraving - Ultimaker 2

I am not sure if it is a good idea to add laser cutting/engraving stuff to a machine that is not designed for it.

You would first need to completely cover the machine with a laser-safe enclosure, or else it may be cutting/engraving your skin and eyes too. A laser that can cut through metal, surely can cut through skin, light sensitive eye-cells and even skulls.

And then the rays bouncing around still may be cutting/engraving the inside of the machine: the print head, rods, belts, glass plate, aluminum heated bed, side panels,...

  • Link to post
    Share on other sites
    Posted · Laser attachment for engraving - Ultimaker 2

    I am not sure if it is a good idea to add laser cutting/engraving stuff to a machine that is not designed for it.

    You would first need to completely cover the machine with a laser-safe enclosure, or else it may be cutting/engraving your skin and eyes too. A laser that can cut through metal, surely can cut through skin, light sensitive eye-cells and even skulls.

    And then the rays bouncing around still may be cutting/engraving the inside of the machine: the print head, rods, belts, glass plate, aluminum heated bed, side panels,...

     

    While I agree that you shouldn't look directly at it or stick your fingers under the laser, those units do need to be focused to actually cut anything... So I wouldn't worry too much about damaging the machine... You do need to be careful with your eyes though.

  • Link to post
    Share on other sites
    Posted · Laser attachment for engraving - Ultimaker 2

     

    I am not sure if it is a good idea to add laser cutting/engraving stuff to a machine that is not designed for it.

    You would first need to completely cover the machine with a laser-safe enclosure, or else it may be cutting/engraving your skin and eyes too. A laser that can cut through metal, surely can cut through skin, light sensitive eye-cells and even skulls.

    And then the rays bouncing around still may be cutting/engraving the inside of the machine: the print head, rods, belts, glass plate, aluminum heated bed, side panels,...

     

    While I agree that you shouldn't look directly at it or stick your fingers under the laser, those units do need to be focused to actually cut anything... So I wouldn't worry too much about damaging the machine... You do need to be careful with your eyes though.

     

    Engraving isn't that powerful than cutting, lasers can be slightly powerless so it could work...

    Beside yes of course you still have to securize your engraving area but a small laser that we can already find in small DIY projects .

  • Link to post
    Share on other sites
    Posted · Laser attachment for engraving - Ultimaker 2

    While I agree that you shouldn't look directly at it or stick your fingers under the laser, those units do need to be focused to actually cut anything... So I wouldn't worry too much about damaging the machine... You do need to be careful with your eyes though.

     

    Ha, okay. That makes things a bit easier. When I hear the word "laser", I still think of those big, old devices we had in school, emitting light that runs for 100km in a knife-sharp beam. Sort of scrap military or scientific stuff. :)

    But that said, I still would wear very dark laser-safe glasses, as long as spare eyes are not available on the market...

  • Link to post
    Share on other sites
    Posted · Laser attachment for engraving - Ultimaker 2

    Look at the Endurance laser engraver. I think that with attention to safety features it could be added, and the higher power version might even cut 1.5 mm wood or acrylic, which would suit me. I am keen for someone with more engineering ability than me to try, so that they can tell me how to do it

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker Transformation Summit

        On April 20 - April 23 we will host the Ultimaker Transformation Summit. Come talk to us via Live chat and get inspired by any of our relevant presentations!
        • 6 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...