Jump to content
Ultimaker Community of 3D Printing Experts

Cura 15.04.6 or Cura 2.1.2 That is the question


Recommended Posts

Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

I have been away from the printer for some time and just getting back into having some fun. Yesterday I converted my UM2 to the + version which went well. Firmware updated from Cura 15.04.6 after installation.

I now notice there are 2 versions of Cura running alongside each other and don't seem to be able to find anything discussing the pros and cons for each version.

I am running windows 7 64bit. so I am guessing the 2.1.2 version is possibly where I should go but unsure.

I have seen the amendments to the material.txt file needed for the different nozzles but other than that I am scratching my head.

What do you folks think of the new version ?

Nigel

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    As the only dev to do work on both versions I can name quite a few differences. The most notable one are pretty much invisible to users (The old architecture was a pretty big mess)

    For normal use it pretty much comes down to;

    2.1 -> More features, slightly slower slicing (but better handling of edge cases), slower layer view, a ton of extra settings, easier to expand. Will continue to get updates / development. Faster rendering.

    15.04 -> Less features, somewhat faster slicing, faster layer view, can load g-code files. Won't get updates anymore in the near future.

    • Like 1
    Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Hi nallath,

    Can old and new (>2.1) Cura versions be installed parallel on the same system, without messing each other's settings up? Do they use separate directories and files?

    If so, people could simply install both, and use the version that works best for a particular task. Or they could just keep the old one as a fall-back.

    Geert

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    i have both installed and use both depending on the project. when i want to throw something at the printer without much thinking or if there is lots of details in the layer view, i use 15.04, but most of the time, I have settled for 2.1.2.

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    If so, people could simply install both, and use the version that works best for a particular task. Or they could just keep the old one as a fall-back.

     

    Yep. You'd almost think we designed software so it's easy for us to use and compare ;)

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    OK thanks for the comments. I will load up the new version and start wrapping my head around it.

    I will run them both for a while just in case something gives.

    Looks like fun!

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Thanks!

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Old one or Simplify3D all day, Cura 2.1.2 is hopeless.

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Does 15.04.6 and 2.1.2 use the same version of Marlin, or do we need to keep swapping?

  • Link to post
    Share on other sites
    Posted (edited) · Cura 15.04.6 or Cura 2.1.2 That is the question

    Does 15.04.6 and 2.1.2 use the same version of Marlin, or do we need to keep swapping?

     

    They use the same version. No worries :) We will stop to update the old Cura at some point in time (This also means that at some point you will need to use cura 2.x if you want new firmware)

    Edited by Guest
  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Well I am getting on pretty OK with the new version now. Perhaps its the never-ending list of settings that are available now and making sure the ones I need are on the main view.

    Working well I have to say :)

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Old one or Simplify3D all day, Cura 2.1.2 is hopeless.

    Simplify3D or Formide. Cura-BCN3D-0.1.5-beta is also hopeless!

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Simplify3D or Formide. I'm struggling with Cura and dual extrusion machines and those two don't give me issues. Cura-BCN3D-0.1.5-beta is also hopeless!

  • Link to post
    Share on other sites
    Posted (edited) · Cura 15.04.6 or Cura 2.1.2 That is the question

    Formide is actually a fork of CuraEngine. Dual extrusion will also have received tweaks in 2.2

    Edited by Guest
    • Like 1
    Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    I use 2.1.2 for the new supports capability and I like the concentric top/bottom fill patterns. I only do PLA and ABS with it though.

    For everything else (other materials, no supports needed, etc.) I use 15.04.6. It's more complete, faster, and just works. But supports are terrible.

    Once 2.x grows more, I can see transitioning to it fully, but certainly not yet. It's just a baby, give it time to grow strong before you put it in the work force. :)

    Just my $0.02.

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Will Cura 2.1 be able to load gcode files eventually?

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    14.09 is the best version I've used (and still do).

    Later versions (definitely 15.02 and later) all cause prints to take much longer than necessary.

    I think it's related to the way retraction is performed but I've not quite worked out exactly what changed.

    It's a shame really because I would like to use the new features in 2.x but I can't accept an increase in print time of 25 to 100 %.

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Will Cura 2.1 be able to load gcode files eventually?

     

    Yes. But it's not planned for 2.2

  • Link to post
    Share on other sites
    Posted (edited) · Cura 15.04.6 or Cura 2.1.2 That is the question

    14.09 is the best version I've used (and still do).

    Later versions (definitely 15.02 and later) all cause prints to take much longer than necessary.

    I think it's related to the way retraction is performed but I've not quite worked out exactly what changed.

    It's a shame really because I would like to use the new features in 2.x but I can't accept an increase in print time of 25 to 100 %.

     

    Does it actually increase or is it just the estimation that is different? I very much doubt that the actual print time increases by 100% by something that happened between 14.09 and 15.02. Especially because after two years you're the first person to report the issue.

    Edited by Guest
  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    I also have both installed and it really depends what you need the slicer for.

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Why is the cura 15.04.6 the old UI again? I must have missed this point... does not make any sense.

    J

  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    15.04.x are the legacy versions. It's still the old interface not again...

  • Link to post
    Share on other sites
    Posted (edited) · Cura 15.04.6 or Cura 2.1.2 That is the question

     

    14.09 is the best version I've used (and still do).

    Later versions (definitely 15.02 and later) all cause prints to take much longer than necessary.

    I think it's related to the way retraction is performed but I've not quite worked out exactly what changed.

    It's a shame really because I would like to use the new features in 2.x but I can't accept an increase in print time of 25 to 100 %.

     

    Does it actually increase or is it just the estimation that is different? I very much doubt that the actual print time increases by 100% by something that happened between 14.09 and 15.02. Especially because after two years you're the first person to report the issue.

     

    Sorry for the delay in replying I have been on holiday

    I have reported this before.

    I have read posts of at least one other person who has noticed the same thing.

    The time increase is REAL not estimated.

    It depends on the item being printed but yes the print time increases by 100 % for some objects and a significant amount for all objects.

    Edited by Guest
  • Link to post
    Share on other sites
    Posted · Cura 15.04.6 or Cura 2.1.2 That is the question

    Well @prb4 if you want someone to fix this, please post an STL and the 2 gcode files created so someone can analyze what is different and maybe make an improvement to the latest cura. Really the entire gcode files need be posted as that will include any scaling you did, multiple objects, and will include all settings. You can't post them here so post them in dropbox or some other web site that you have control over (preferably not something that will only host the files for a month).

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker Transformation Summit

        On April 20 - April 23 we will host the Ultimaker Transformation Summit. Come talk to us via Live chat and get inspired by any of our relevant presentations!
        • 6 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...