Jump to content
Ultimaker Community of 3D Printing Experts

UMO+ resets after printhead fan starts


Incalculable
 Share

Recommended Posts

Posted · UMO+ resets after printhead fan starts

Dear Ultimaker colleagues,

First of all "Hello from Austria", since that is my first post ;-)

I've just finished my UMO+ and expirience a problem to which i find no answer in the support section:

When printing the printer works perfect for the brim and first layer, but approximately 5 seconds after the fan starts the whole UMO+ seems to reset (Ulticontroller goes blank, restarts, shows SD Card Ready, print stoppen).

I now disconnected the fan from the board and print without fan and it works fine.

To me it seems as if the power safety resets the board. I also retried to plugin the fan, but then i've the same reset again.

Newest firmware is installed.

Do you have any ideas?

Thank you for your help!

Rgds Vinc

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    So the fan starts up and spins as it should before the machine resets? I would've suspected a short in the fan, but if it actually spins up and works first that sound strange (unless the movement of the head causes the short after a while). I don't suppose you have another fan laying around to test?

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Yes, the Fan starts, then after 5 seconds comes the reset. A short due to movement of the Head? Hmm.. I'll look into that..

     

    So the fan starts up and spins as it should before the machine resets? I would've suspected a short in the fan, but if it actually spins up and works first that sound strange (unless the movement of the head causes the short after a while). I don't suppose you have another fan laying around to test?

     

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    FYI: I just manually switched on the fan-works without fault, also when printhead is moved manually.

    Thereafter activated heated bed and nozzle together with fan - no fault.

    Therafter printed without fan- no fault.

    Activated fan during print- 3seconds then reset, arghhh!!

     

    Yes, the Fan starts, then after 5 seconds comes the reset. A short due to movement of the Head? Hmm.. I'll look into that..

     

    So the fan starts up and spins as it should before the machine resets? I would've suspected a short in the fan, but if it actually spins up and works first that sound strange (unless the movement of the head causes the short after a while). I don't suppose you have another fan laying around to test?

     

     

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Can you check with another sd card? Or another file?

    I had once a problem like that but was a dead heater after a a lot of mods and a lot of tinkering the machine. Can you check also the feeder cables, you can heat to 170C or more and go Prepare/Move axis/Move 0.1/Extruder to make the extruder push filament. Just to check if that triggers the reset.

    Also I would reinstall the latest firmware before doing more tests (just in case) and also after that try to do Control/Reset factory default settings (or something like that).

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Okay, i rerouted the fan cable- no change. Thereafter tried to reproduce the failure by moving the axles - but the failure is not reproducable, it's not connected to a specific axle. And it one time shut down without fan when setting the nozzle temperature to a higher setting. For me it seems as if the system as whole is at the limit of the safety of the board and the fan "pushes it over". Perhaps the heater cartridge uses to much energy?

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Okay, when i set a higher temperature during print- reset. Lowering isn't a problem.

    That would be consistent with the fan, because the fan will cool the nozzle and the heater will therefore switch on some seconds after the fan. And then ....restart.

    So i think the heater cartridge takes to much power.. Since the UMO+ is brandnew i'll try to contact the Ultimaker support on monday...

    Rgds Vinc

    • Like 1
    Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Hey guys,

    The finder relais on the mainboard is switching and causing the reboots when using to much power. Meaning e.g. without heated bed the printer works fine, when i switch it on then reboot.

    Is anybody out there who had the same problem? I triple checked all the wirings and i'm a hundred percent sure they're not the rootcause. I think the mainboard or the heater cartridge have a defekt. What so you think?

  • Link to post
    Share on other sites

    Posted · UMO+ resets after printhead fan starts

    Hey guys,

    The finder relais on the mainboard is switching and causing the reboots when using to much power. Meaning e.g. without heated bed the printer works fine, when i switch it on then reboot.

    Is anybody out there who had the same problem? I triple checked all the wirings and i'm a hundred percent sure they're not the rootcause. I think the mainboard or the heater cartridge have a defekt. What so you think?

    I (unfortenately) have the same problem. It occurs to me after I swapped out my heater Cartridge... I don't think it is a broken PCB. My guess is that the printer is consuming more power. That means, that the PSU or the heater-cartridge is the wrong one. (I got an UM2 one with 40Watts and 24Volts -> but it should work anyways) Im going to contact my german reseller tomorroe and I'm going to see, what they can say... Have you fixed your problem?

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 11 replies
    ×
    ×
    • Create New...