Jump to content

"zulässige"/normale Abweichung Drucktemperatur?


DirkT

Recommended Posts

Posted (edited) · "zulässige"/normale Abweichung Drucktemperatur?

Hallo,

ich habe einen Ultimaker 2+.

in welchem Bereich darf die Drucktemperatur vom Soll abweichen?

Meine Abweichung der Drucktemperatur beträgt derzeit max. +-2°C(218°C - 222 °C, eingestellt sind 220°C bei PLA).

Ist das im grünen Bereich?

Danke für Eure Hinweise/Antworten.

Gruß,

Dirk

Edited by Guest
  • Link to post
    Share on other sites

    Posted (edited) · "zulässige"/normale Abweichung Drucktemperatur?

    Hallo Dirk,

    4C würde ich sagen ist OK

    Wann hast du diese Abweichung?

    Irgendwann nach dem Druck start (wenn Fan 100% drehen) sollte sich die Temp. einblenden. Wenn du aber z.B. das Infill recht schnell Druckst ist die Abweichung auch normal da dass Infill mehr Temperatur beansprucht (Firmware/Patrone heizt nach) dann kommen die Außenwände die wo langsamer gedruckt werden so entsteht Temp. Überschuss (Firmware regellt wieder) so ensteht dann die Temp. Schwankung

    Gruß Gerd

    Edited by Guest
    Schreibfehler "±" entfernt
  • Link to post
    Share on other sites

    Posted (edited) · "zulässige"/normale Abweichung Drucktemperatur?

    Hallo Gerd,

    danke für die Info. Wann genau die Abweichung ist, kann ich gar nicht so genau sagen, aber ich denke, es ist so wie Du beschrieben hast(Temperaturunterschied wegen langsam gedruckter Aussenwände & schneller gedrucktem Infill).

    Ich achte das nächste mal genauer drauf und mach mal einen Screenshot. Dank Octoprint wird das ja grafisch dargestellt.

    Gruß,

    Dirk

    Edited by Guest
  • Link to post
    Share on other sites

    Posted (edited) · "zulässige"/normale Abweichung Drucktemperatur?

    Hallo,

    ich setze ja bei meinem Ultimaker 2 Extended + die Tinker V16.08.2 ein. Dort habe ich die PID-Werte angepasst.  Die neuen Werte habe ich von TinkerGnome Firmware Seite und bin sehr zufrieden:

    Kp = 12.00; Ki = 0.75; Kd = 55.00

    Ursprünglich sind die Werte für den Olsson Block, passen aber auch für meinen 3DSolex MATCHLESS RACE Block. Die Temperaturkurve ist jetzt gleichmäßiger.

    Gruß,

    Dirk

    PS.: Der Vollständigkeit halber, meine alten Werte waren:

    Kp = 10.03; Ki = 1.50; Kd = 70.00

    Edited by Guest
  • Link to post
    Share on other sites

    Posted (edited) · "zulässige"/normale Abweichung Drucktemperatur?

    Es gibt auch noch PID Autotune, dass eigentlich noch bessere Werte erzeugen soll?

    Du hörst "eigentlich" bei mir macht das PID Autotune Funktion was es will, mit den Werten was die Funktion ermittelt habe ich 15C Temperatur Schwankungen.

    Aber einen versuch ist es Werte wen'st du persönliche genau abgestimmte Werte benötigst.

    Das ganze PID Autotuning Funktion ist auch über der Firmware möglich.

    Gruß Gerd

    Edited by Guest
  • Link to post
    Share on other sites

    Posted · "zulässige"/normale Abweichung Drucktemperatur?

    Hallo Gerd,

    autotune liefert bei mir nur eine Fehlermeldung. Er fängt an und bricht dann ab, weil die Temperatur zu hoch wird?! Schon mit dem Olson-Block. Keine Ahnung wieso.

    Habe den Temp.-Sensor und die Heizpatrone(35W von 3D Solex) getauscht. Das hat nichts gebracht.

    Aber anbei mal eine Temp.-Kurve aus Octoprint. Derzeit +- 1 °C max.

    Temperaturdiagramm.thumb.jpg.5ed9c910e0c0ab6df8fd40f93c26b335.jpg

    Damit bin ich sehr zufrieden!

    Gruß,

    Dirk

    Temperaturdiagramm.thumb.jpg.5ed9c910e0c0ab6df8fd40f93c26b335.jpg

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...