Jump to content
Ultimaker Community of 3D Printing Experts

UM 2 print bed raising too quickly at beginning of print (with video of problem)


Recommended Posts

Posted (edited) · UM 2 print bed raising too quickly at beginning of print (with video of problem)

I have an Ultimaker 2. Just recently when I begin prints, after the print head extrudes a bit of PLA (with the print bed the normal distance from nozzle) as the print head moves from the front left corner to the middle to begin printing, instead of gradually moving up to the nozzle, the print bed moves immediately to 1mm away from the nozzle, even with the nozzle in the front left corner.  The nozzle almost hits the metal clip on the print bed and the pre-extruded plastic clogs on the nozzle, not allowing anything to print properly.

Has anyone seen this problem before? I did a factory reset on the machine, and it is still having the same problem.

Here is a video of the problem:

Edited by Guest
  • Link to post
    Share on other sites
    Posted · UM 2 print bed raising too quickly at beginning of print (with video of problem)

    Hm. There is not any start/end.GCode in UltiGCode.

    As far as i can see, the first Z-Move in UltiGCode is a combined move like this:

    ..

    ;LAYER:0

    M107

    G10

    G0 F2400 X103.645 Y103.403 Z.27 //combined move to print start

    ..

    And if so in your GCode, than the Z-Move to 0 must be initiate by firmware.

    In this case, i suspect the problem in the firmware.

  • Link to post
    Share on other sites
    Posted · UM 2 print bed raising too quickly at beginning of print (with video of problem)

    Hm. There is not any  start/end.GCode in UltiGCode.

    As far as i can see, the first Z-Move in UltiGCode is a combined move like this:

    ..

    ;LAYER:0

    M107

    G10

    G0 F2400 X103.645 Y103.403 Z.27  //combined move to print start

    ..

     

    @gaschoa

    Which Cura version are you using?

    I remember that the first move command looks different, if the skirt is "misused" as a replacement for brim (line count > 1 and/or a very small start distance).

    Can you show us the first few lines of the gcode file?

  • Link to post
    Share on other sites
    Posted · UM 2 print bed raising too quickly at beginning of print (with video of problem)

    I looked at my skirt settings and it was set to '0' so I changed it to '1' and the print bed functioned properly. Attached is a photo of the settings in Cura 15.04.6 that was causing the problem.

    Skirt_Settings.thumb.png.69f772e8b330e7299d2611aa2f6bef68.png

    Skirt_Settings.thumb.png.69f772e8b330e7299d2611aa2f6bef68.png

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...